Control Microsystems SCADAPack LP страница 42 Скачать руководство пользователя

Страница: 42 / 47

14 Specifications

Disclaimer: Control Microsystems reserves the right to change product specifications without
notice. For more information visit

www.controlmicrosystems.com

14.1 General

I/O Terminations

8 and 10 pole, removable terminal blocks.
12 to 22 AWG
15A contacts

Dimensions

8.40 inch (213mm) wide
5.00 inch (127 mm) high
1.80 inch (45mm) deep

Packaging

Corrosion resistant zinc plated steel with black enamel paint

Environment

5% RH to 95% RH, non-condensing
–40

C to 70

–40

F to 158

14.2 Controller

Processors

16-bit CMOS microcontroller, 14.74MHz clock
integrated watchdog timer
microcontroller co-processor, 14.74MHz clock

Memory

1MBytes CMOS RAM
512kBytes flash ROM
1kBytes EEPROM

Non-volatile
RAM

CMOS RAM with lithium battery retains contents for 2 years
with no power

Clock calendar

1 minute/month at 25°C

+1/–3 minutes/month 0 to 50°C

Internal
temperature

Measurement range -40°C to 75°C. Accuracy

5°C.

Measurement range -40°F to 167°F. Accuracy

9°F.

Lithium battery
monitor

Accuracy

0.2V.

14.3 Communications

Communication
Port COM1

RS-485 serial port
removable terminal block
2 wire half duplex
Bias resistors installed.

Communication
Port COM2

RS-232 compatible serial port (CMOS)
Data Terminal Equipment (DTE)
8 pin modular jack
Full or half duplex with RTS/CTS control
Implemented Td, Rd, CTS, RTS, DCD, DTR, 5V power with
jumper link.

SCADAPack LP Hardware Manual
May 26, 2006

Содержание SCADAPack LP
















































Результаты поиска

Содержание SCADAPack LP

Отзывы:

Похожие инструкции для SCADAPack LP

Бренды по названию

Популярные бренды

Control Microsystems SCADAPack LP, Руководство по оборудованию

Результаты поиска

Содержание SCADAPack LP

Отзывы:

Похожие инструкции для SCADAPack LP

Бренды по названию

Популярные бренды