manualshive.com logo in svg

Control Microsystems SCADAPack LP, Руководство по оборудованию

Поделиться
Скачать
Control Microsystems SCADAPack LP Скачать руководство пользователя страница 25

10 Serial Communication 

The SCADAPack LP controller is equipped with three serial communication ports. Two of the serial 
communication ports support RS-232 serial communication and one port supports RS-485 serial 
communication.  

Serial ports on the SCADAPack LP controller are designated COM1, COM2 and COM3. Refer to 

Figure 2:  SCADAPack LP Board Layout

 for the location of the serial ports. 

10.1 

RS-232 Serial Communications Ports 

The two RS-232 serial ports are designated COM2 and COM3. 

All RS-232 wiring must use shielded cable. The shield should be connected to chassis ground at one 
point. Failure to properly shield the cable may result in the installation not complying with FCC or 
DOC radio interference regulations. 

10.1.1 

COM2 RS-232 Serial Port 

The following table shows the serial and protocol communication parameters supported by COM2. 
These parameters are set from TelePACE, ISaGRAF Workbench or from an application program 
running in the SCADAPack LP controller. Default values are set when a Cold Boot or Service Boot 
is performed on the SCADAPack LP controller. 

Parameter 

Supported Values 

Baud Rate 

300, 600, 1200, 2400, 4800, 9600, 19200 and 38400
Default: 9600 

Duplex 

Full or Half 
Default: Full 

Parity 

Odd, None or Even 
Default: None 

Data Bits 

7 or 8 Bits 
Default: 8 Bits 

Stop Bits 

1 or 2 Bits 
Default: 1 Bit 

Receive Flow Control  

ModbusRTU or None 
Default: ModbusRTU 

Transmit Flow Control 

Ignore CTS or None 
Default: None 

Station 

1 to 65534 
Default: 1 

Protocol 

None, Modbus RTU or Modbus ASCII 
Default: Modbus RTU 

Addressing Mode 

Standard or Extended 
Default: Standard 

SCADAPack LP Hardware Manual 
May 26, 2006 

 

24

Содержание SCADAPack LP
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды