Control Microsystems SCADAPack LP страница 24 Скачать руководство пользователя | Manualshive

Страница: 24 / 47

background image

sensor. Note the use of shielded wiring and that the shield is connected at one end only. Counter 2 is
shown connected to an external turbine meter pre-amplifier.

When connecting to a turbine meter amplifier the manufacturer may have a specific current
requirement to power the pre-amplifier. The SCADAPack LP includes a 1000-ohm resistor from the
counter input to the DC input power source. This is the recommended wiring for a Halliburton Low
Power Pre-Amp when the SCADAPack LP is powered from 12V. If this resistor is not suitable for
your external amplifier then do not connect the jumper in either position. On Counter 1, the J11
jumper would be removed. On Counter 2, the J12 jumper would be removed. Wire the amplifier as
per the manufacturers recommendations.

Counter Inputs 1 and 2 can be used with conventional sources such as open collector transistors and
contacts. The SCADAPack LP includes a 1000-ohm resistor from the counter input to the DC input
power source. This resistor can be used when the SCADAPack LP is powered from 12V. On
Counter 1, J11 would be in the External Amplifier or bottom position. On Counter 2, J12 would be
in the External Amplifier or bottom position. If a higher voltage is used or a pullup current other than
12V at 1000-ohms is required then the user must wire an external resistor to an appropriate power
source. On Counter 1, the J11 jumper would be removed. On Counter 2, the J12 jumper would be
removed.

J9

J11

Internal

amplifier

To counter 1

Counter 1 input

Internal 1000

ohms connected

to Input Voltage

J10

J12

Internal

amplifier

To counter 2

Counter 2 input

Internal 1000

ohms connected

to Input Voltage

12VDC PWR IN

12VDC PWR
IN

Figure 8: Counter Jumpers

SCADAPack LP Hardware Manual
May 26, 2006

23

«
...
22
23
24
25
26
...
»

Содержание SCADAPack LP
















































Отзывы:

Нет отзывов

Похожие инструкции для SCADAPack LP

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: Unitech Страницы: 11

Бренд: B meters Страницы: 10

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

REVOLUTION Pro Controller 2

Бренд: Nacon Страницы: 11

Бренд: Nacon Страницы: 18

Бренд: Nacon Страницы: 24

Бренд: Nabco Страницы: 35

Бренд: X-lander Страницы: 72

Бренд: X Rocker Страницы: 38

DuetPro Carrycot

Бренд: Qtus Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды