background image

 

 

   1800

 

Continental Blvd. Suite 200 

 Charlotte, NC 28273 

   866-424-4489 

 snapone.com 

 

 

AVERTISSEMENT!

 Pour réduire le risque de choc électrique, 

n'exposez pas cet appareil à la pluie ou à l'humidité. 

 

Save these instructions 

Conservez ces instructions 

 
Compliance of this equipment is confirmed by the following label that is placed on the equipment: 

Conformité de cet appareil est confirmé par le symbole suivant qui est placé sur l'équipement:

 

 

 

 

 

 
 

USA & Canada Compliance 

 

FCC Part 15, Subpart B & IC Unintentional Emissions Interference Statement 

 
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC rules.  These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a residential installation.  This 
equipment generates uses and can radiate radio frequency energy and, if not installed and used 
in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation.  If this 
equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 
 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 
This device complies with part 15 of the FCC rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation. 

 

Cet appareil est conforme à la section 15 des règles. Son utilisation est soumise aux deux 
conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles et (2) cet 
appareil doit accepter toutes les interférences reçues, y compris celles pouvant entraîner un 
fonctionnement non souhaité. 
 
IMPORTANT! Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate this equipment. 
 
IMPORTANT! Tous les changements ou modifications pas expressément approuvés par la partie 
responsable de la conformité ont pu vider l’autorité de l’utilisateur pour actionner cet équipement. 
 

Содержание CORE-3












Отзывы: