background image

© 2000 CONTRIVE • B1401|400.EN 

0211

 

4

 

www.contrive.it 

CYCLE

 

 

 

MANUAL SHUTDOWN 

UNIT HAS BEEN PUT OUT OF SERVICE FROM 
PUSH BUTTON. PUSH AGAIN TO RESTORE. 

 

 

 

IGNITION 

1

ST

 SAFETY TIME. BURNER IGNITION TRIAL 

WITH PILOT GAS VALVE OPEN.

 

 

TIMER SHUTDOWN 

BURNER HAS BEEN TURNED OFF BY 
OPTIONAL INTERNAL TIMER.

 

 

 

 

PILOT BURNER ON 

PILOT GAS VALVE IS OPEN, BURNER ON 
UNTIL SHUTDOWN, LOCKOUT OR FAILURE

 

 

THERMOSTAT SHUTDOWN 

BURNER HAS BEEN TURNED OFF BY LOCAL 
THERMOSTAT AT TERMINAL 22.

 

 

 

 

POSTCOMBUSTION 

WAITING FOR FLAME QUENCHING AFTER 
LOCKOUT OR SHUTDOWN REQUEST.

 

 

PREPURGE 

PURGE OF COMBUSTION CHAMBER OR MIN 
TIME FOR ILLEGAL FLAME PROVING.

 

 

 

 

POSTPURGE 

PURGE OF COMBUSTION CHAMBER, SHOWN 
TOGETHER WITH ASSOCIATED CODE.

 

 

LOCKOUTS 

 

 

STANDBY 

WAITING FOR RESET WHEN PROGRAMMED 
FOR STANDBY MODE AT POWER-ON.

 

 

 

 

FLAME LOSS 

FLAME QUENCHING DURING NORMAL 
BURNER OPERATION.

 

 

ILLEGAL DETECTION 

PARASITE FLAME DETECTION DURING PRE-
PURGE, POSTPURGE OR POSTCOMBUSTION.

 

 

 

 

CONTROL BOARD COM FAILURE 

EXPANSION CONTROL BOARD IS MISSING OR 
NOT WORKING PROPERLY. 

 

 

IGNITION FAILURE 

NO FLAME DETECTED AT THE END OF 
IGNITION TRIAL, 1

ST

 SAFETY TIME.

 

 

 

 

 

 

RESETABLE FAILURES 

 

 

IGNITION DEVICE FAILURE 

IGNITION DEVICE UNPLUGGED, DEFECTIVE 
OR NOT WORKING PROPERLY.

 

 

 

 

MISSING GROUND JOINT | SOFT JUMP 

POOR SPARK RETURN PATH (I.E.: BAD 
GROUND CONNECTION TO BURNERS HEAD).

 

 

GAS VALVE FAILURE 

GAS VALVE(S) UNPLUGGED, DEFECTIVE OR 
NOT WORKING PROPERLY.

 

 

 

 

STRONG EMI | CONFIG ERROR 

ELECTRO MAGNETIC INTERFERENCE ABOVE 
ADMISSIBLE LIMIT, CONFIGURATION ERROR.

 

 

OUTPUT RELAYS FAILURE 

SHORT CIRCUIT ON OUTPUT RELAY CONTACT 
LOADS DISCONNECTED BY SAFETY RELAY.

 

 

 

 

TIMEBASE FAILURE 

MISMATCH BETWEEN 1

ST

 AND 2

ND

 INTERNAL 

TIMEBASE GENERATORS.

 

 

CONTROL BOARD ERROR 

WRONG OPERATION OF CONTROL BOARD, 
ILLEGAL COMMAND

 

 

 

 

SYSTEM WATCHDOG 

MICROPROCESSOR ISN’T OPERATING 
PROPERLY.

 

 

 

NON RESETABLE FAILURES 

 

 

PUSH BUTTON FAILURE 

PUSH BUTTON FOUND CLOSED AT SELF TEST. 
FAILURE OR AVOID PUSHING DURING TEST. 

 

 

 

MASTER SAFETY RELAY FAILURE 

SHORT CIRCUIT ON SAFETY RELAY CONTACT. 
OUTPUT RELAYS WILL DISCONNECT LOADS.

 

 

SYSTEM ERROR 

PROGRAM ERRORS, CORRUPTION IN 
FIRMWARE MEMORY.

 

 

 

 

 

 

Содержание Quad400













Отзывы: