Continental Fireplaces CDCS600-P, Инструкция по установке и эксплуатации, Страница: 4 / 24

4
W415-0162 / E / 03.05.04
4 NUTS
SHIPPING
BRACKET
CS600:
Maximum input is 35,000 BTU/hr for natu-
ral gas and 31,500 BTU/hr for propane. This stove is
approved for bedroom and bed-sitting room installa-
tions.
CDVS600: TOP VENT / REAR VENT
VERTICAL TERMINATION:
Maximum in-
put is 35,000 BTU/hr for natural gas and 31,500 BTU/hr
for propane. Maximum output for natural gas is 27,300
BTU/hr at an efficiency of 78%. Maximum output for pro-
pane is 24,570 BTU/hr at an efficiency of 78%. Maxi-
mum A.F.U.E. (annual fuel utilization efficiency) rating is
72% for natural gas and 71% for propane.
REAR VENT HORIZONTAL TERMINA-
TION:
Maximum input is 21,000 BTU/hr for natural
and propane gas. This application requires changing
the main burner orifice.
This stove is not approved for closet or recessed instal-
lations. It is approved for bathroom, bedroom and bed-
sitting room installations.
This stove may be installed in an aftermarket perma-
nently located, manufactured (mobile) home, where not
prohibited by local codes.
Change in flame appearance from "HI" to "LO" is more evi-
dent in natural gas than in propane. Expansion / contraction
noises during heating up and cooling down cycles are nor-
mal and to be expected.
This appliance is only for use with the type of gas indicated
on the rating plate.
(See page 14). This appliance is not
convertible for use with other gases, unless a certified kit
is used.
INSTALLER: It is your responsiblity to check off the
appropriate box on the rating plate according to the
model, venting and gas type of the unit.
Do not use abrasive cleaners to clean these parts. Buff
lightly with a clean dry cloth.
The glass is
3 /
16
" ceramic glass available from your
Continental / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE
MATERIALS. Clean the glass after the first 10 hours of op-
eration with a recommended gas fireplace glass cleaner.
Thereafter clean as required. DO NOT CLEAN GLASS
WHEN HOT! If the glass is not kept clean permanent dis-
colouration and / or blemishes may result.
To avoid the stove being damaged during shipping, a ship-
ping bracket has been used and must be unbolted before
the stove can be installed.
1. Remove the four nuts holding the shipping bracket to the
bottom of the stove.
2. Lift the stove up and away from the skid to clear the
threaded bolts sticking through the bracket. Set down on a
flat surface.
The stove top is not secured to the unit.
3. Discard the nuts, bracket and the skid.
FIGURE 1
THIS GAS STOVE SHOULD BE INSTALLED AND SERVICED
BY A QUALIFIED INSTALLER
to conform with local codes.
Installation practices vary from region to region and it is important
to know the specifics that apply to your area,
for example: in Massachusetts State:
• The fireplace damper must be removed or welded in the open
position prior to installation of a fireplace insert or gas log.
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36 inches.
• The appliance is not approved for installation in a bedroom or
bathroom unless the unit is a direct vent sealed combustion
product.
• WARNING: This product must be installed by a licensed plumber
or gas fitter when installed within the commonwealth of
Massachusetts.
In absence of local codes, install to the current CAN1-B149
Installation Code in Canada or to the National Fuel Gas Code,
ANSI Z223.1, and NFPA 54 in the United States. Mobile home
installation must conform with local codes. In the absence of
local codes, install to the current standard for gas equipped
mobile housing CAN/CSA Z240 MH Series in Canada or the
manufactured home construction and safety standard, Title 24
CFR, part 3280, or the Fire Safety Criteria for manufactured
home installations, Sites and Community Standard ANSI/NFPA
501A in the United States.
Purge all gas lines with the glass door of the stove removed.
Assure that a continuous gas flow is at the burner before re-
installing the door.
Under extreme vent configurations, allow several minutes (5-
15) for the flame to stabilize after ignition.
It is recommended that all horizontal runs have a ¼ inch rise
per foot.
Objects placed in front of the stove must be kept a minimum
of 48" away from the front face of the unit.
The stove and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of 1/2 psig (3.5 kPa). The
stove must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal to
or less than ½ psig (3.5 kPa).
The stove, when installed with a blower, must be electrically
connected and grounded in accordance with local codes. In the
absence of local codes, use the current CSA C22.1 CANADIAN
ELECTRICAL CODE in Canada or the ANSI/NFPA 70-1996
NATIONAL ELECTRICAL CODE in the United States. The blower
power cord must be connected into a properly grounded receptacle.
The grounding prong must not be removed from the cord plug.
FOR YOUR SATISFACTION, THIS STOVE HAS BEEN TEST-
FIRED TO ASSURE ITS OPERATION AND QUALITY!
Minimum inlet gas supply pressure is 4.5 inches water column for
natural gas and 11 inches water column for propane. Maximum
inlet gas pressure is 7 inches water column for natural gas and 13
inches water column for propane. When the valve is set to "HI", the
manifold pressure under flow conditions is 3.5 inches water column
for natural gas and 10 inches water column for propane. When the
fireplace is installed at elevations above 4,500ft, and in the absence
of specific recommendations from the local authority having juris-
diction, the certified high altitude input rating shall be reduced at the
rate of 4% for each additional 1,000ft.
GENERAL INSTRUCTIONS
GENERAL INFORMATION
CARE OF GLASS, AND PLATED PARTS
SHIPPING BRACKET