Continental Fireplaces BCDV36CFNTR, Инструкция по установке и эксплуатации

Страница: 23 / 128

23
W415-1516 / A / 10.22.15
EN
90°
V
1
V
2
H
1
H
2
90°
90°
H
3
45°
18.2_3A
Example:
V
1
= 1.5 FT (0.5m)
V
2
= 5 FT (1.5m)
V
T
= V
1
+ V
2
= 1.5FT (0.5m)+ 5FT (1.5m) = 6.5 FT (2m)
H
1
= 1 FT (0.3m)
H
2
= 1 FT (0.3m)
H
3
= 10.75 FT (3.3m)
H
R
= H
1
+ H
2
+ H
3
= 1FT (0.3m) + 1FT (0.3m) + 10.75FT (3.3m) = 12.75FT (3.9m)
H
O
= .03 (four 90° one 45° elbow - 90°)
= .03 (360° + 45° - 90°) = 6.75 FT (2.1m)
H
T
= H
R
+ H
O
= 12.75FT (3.9m) + 6.75FT (2.1m) = 19.5 FT (5.9m)
H
T
+ V
T
= 19.5FT (5.9m) + 6.5FT (2m) = 26 FT (7.9m)
Formula 1:
H
T
< 3 V
T
3 V
T
= 3FT (0.9m) x 6.5FT (2m) = 19.5FT (5.9m)
19.5FT (5.9m) = 19.5FT (5.9m)
Formula 2:
H
T
+ V
T
< 40 FT (12.2m)
26 FT (7.9m) < 40 FT (12.2m)
Since both formulas are met, this vent configuration is acceptable.
4.0 PRE-INSTALLATION PREPARATION
!
WARNING
FAILURE TO INSTALL THE CAP WILL CAUSE THE APPLIANCE TO FUNCTION IMPROPERLY AND
CAN CAUSE INJURY OR PROPERTY DAMAGE.
4.1 REAR EXIT
4.2 TOP VENT
From inside the fi rebox, insert the 4" (102mm) fl ue pipe / gasket assembly
(provided) through the rear of the fi rebox. Secure the gasket assembly to the rear
and top of the appliance using 4 #8 x ¾ inch Hex Head Wildrill screws supplied.
Do not overtighten. The gasket needs only to be snug against the fi rebox.
Before attaching elbows to the collars on the back of the appliance, 1½" (38mm)
will need to be trimmed off the 4" (102mm) collar.
A.
Remove the 7" (178mm) diameter cap from the top of the appliance and
re-secure it over the 7" (178mm) collar located at the rear of the appliance.
Press fi rmly on the cap while securing to ensure an airtight seal. Do not
damage the gasket.
B.
Remove the plate covering the 4" (102mm) diameter fl ue opening (seen
inside the top of the 7" (178mm) diameter collar) and discard. Try not to
disturb the retaining ring or the gasket beneath. Re-secure the ring and
gasket using the screws removed from the plate.
C.
From inside the fi rebox, insert the 4" (102mm) fl ue pipe / gasket assembly through the heat shield and
out through the retaining ring. Secure the assembly to the rear and top of the appliance using 4 #8 x
¾" Hex Head Wildrill screws supplied. Do not overtighten. The gasket needs only to be snug against
the fi rebox.