Contec CPS-PCS341EC-DS1-1201 Скачать руководство пользователя

Страница: 33 / 44

3 Nomenclature and Functions

CPS-PCS341EC-DS1-1201 Hardware Manual

LAN Port (LAN A, LAN B)

This product has 2 ports of Ethernet.

- Network type

: 100BASE-TX/10BASE-T

- Transmission speed

: 100M/10M bps

- Maximum network path length : 100m /segment

Table 3.5. LAN port

Pin No.

Signal Name

Meaning

TX+

Transmission data(+)output

TX-

Transmission data (-)output

RX+

Received data

(+)input

N.C.

Not connected

N.C.

Not connected

RX-

Received data

(-)input

N.C.

Not connected

N.C.

Not connected

Table 3.6. LED indicator (Side, LAN ports)

LED

Operation

Meaning

Speed(Orange)

Indicates that LAN port is connected by 100Mbps.

OFF

Indicates that LAN port is connected by 10Mbps or

not connected.

Link /Act(Green)

Indicates that LAN port is connected.

Flashing

Indicate that LAN port is transmitting and receiving data with the
connected external device

OFF

Indicates that LAN port is not connected.

Link/Act

Speed

Содержание CPS-PCS341EC-DS1-1201













































Результаты поиска

Содержание CPS-PCS341EC-DS1-1201

Отзывы:

Похожие инструкции для CPS-PCS341EC-DS1-1201

Бренды по названию

Популярные бренды

Contec CPS-PCS341EC-DS1-1201, Руководство по оборудованию

Результаты поиска

Содержание CPS-PCS341EC-DS1-1201

Отзывы:

Похожие инструкции для CPS-PCS341EC-DS1-1201

Бренды по названию

Популярные бренды