Contec CPS-PCS341EC-DS1-1201 страница 17 Скачать руководство пользователя

Страница: 17 / 44

2 Setup

CPS-PCS341EC-DS1-1201 Hardware Manual

Installation Conditions

Installation orientation

You can position the product in the orientation shown below.

Other orientations could cause problems such as inadequate heat dissipation.

Vertical installation (Installation angle 0

)

Figure 2.5. Installation orientation

Make sure to gain proper space between the product and devices that generate heat or exhaust air so that

the ambient temperature stays in the range specified in the environment requirement.

- Recommended installation angle

Recommended installation angle is 0. Other angles may not satisfy the temperature specification of the

product.

- Ambient temperature

The ambient temperature is decided from the multiple measurement points which are a 50mm-distance

from the case. During the operation, adjust the air current to make certain that the temperatures

measured in the points stay within the specified temperature.

- Note that although the ambient temperature is within the specified range, an operational failure may

occur if there is other device generating high heat nearby; the radiation will influence the product to

increase its temperature.

- Do not install the product into the fully-sealed space except the case in which the internal temperature

is adjustable by equipment such as an air conditioner. Long-term usage might increase the temperature

and lead to a malfunction or other troubles.

- When using the product in a high temperature environment, its life time will be shorten. Perform the

forced air cooling to counteract.

CAUTION

Содержание CPS-PCS341EC-DS1-1201













































Результаты поиска

Содержание CPS-PCS341EC-DS1-1201

Отзывы:

Похожие инструкции для CPS-PCS341EC-DS1-1201

Бренды по названию

Популярные бренды

Contec CPS-PCS341EC-DS1-1201, Руководство по оборудованию

Результаты поиска

Содержание CPS-PCS341EC-DS1-1201

Отзывы:

Похожие инструкции для CPS-PCS341EC-DS1-1201

Бренды по названию

Популярные бренды