Congatec 050100 Скачать руководство пользователя страница 62

Страница: 62 / 65

SA70m01

62/65

Table 33.2

Boot Strap Signal Description

Signal

Pin # Description of Boot Strap Signal

I/O

PU/PD

Comment

SPI0_DO

P46

SPI0 master data output (SPI serial output data from SMARC

module to the SPI device

O 1.8V

PU 20k

HDA_SDO /

I2S2_SDOUT

S51

HD audio serial data output to codec

O 1.8V

PD(i) 20k

I2S0_CK

S42

Digital audio clock

I/O 1.8V

PD(i) 20k

Not supported

I2S0_LRCK

S39

Left and right audio synchronization clock

I/O 1.8V

PD(i) 20k

Not supported

Caution

1. The signals listed in the table above are used as chipset configuration straps during system reset. In this condition (during reset), they are

inputs that are pulled to the correct state by either SMARC internally implemented resistors or chipset internally implemented resistors

that are located on the module.

2. No external DC loads or external pull-up or pull-down resistors should change the configuration of the signals listed in the above table.

3. External resistors may override the internal strap states and cause the SMARC module to malfunction and/or cause irreparable damage to

the module.

Table 34 Power and GND Signal Descriptions

Signal

Pin #

Description

I/O

PU/PD Comment

VDD_IN

P147, P148, P149, P150, P151, P152, P153,

P154, P155, P156

Module power input voltage—4.75V min. to 5.25V max.

GND

P2, P9, P12, P15, P18, P32, P38, P47, P50,

P53, P59, P68, P79, P82, P85, P88, P91, P94,

P97, P100, P103, P120, P133, P142

S3, S10, S16, S25, S34, S47, S61, S64, S67,

S70, S73, S80, S83, S86, S89, S92, S101,

S110, S119, S124, S130, S136, S143, S158

Power Ground

VDD_RTC

S147

Low current RTC circuit backup power—3.0V nominal.

May be sourced from a carrier based lithium cell or super cap.

This option requires a customized variant.

BOM option for sourcing

Note

External 3.3 V is required for RTC battery implementation with supercap. Default conga-SA7 configuration does not support supercap charging.

The supercap charging is only possible with a BOM option.

Содержание 050100

































































Результаты поиска

Содержание 050100

Отзывы:

Бренды по названию

Популярные бренды

Congatec 050100, Руководство пользователя

Результаты поиска

Содержание 050100

Отзывы:

Бренды по названию

Популярные бренды