Congatec 050100 Скачать руководство пользователя страница 19

Страница: 19 / 65

SA70m01

19/65

Cooling Solutions

congatec GmbH offers the following cooling solutions for the conga-SA7 variants. The dimensions of the cooling solutions are shown in the
sub-sections. All measurements are in millimeters.

Table 7 Cooling Solution Variants

Cooling Solution

Part No Description

CSP

050150

Passive cooling with 2.7 mm bore-hole standoffs for lidded CPU variants (industrial variants)

050153

Passive cooling with 2.7 mm bore-hole standoffs for bare-die CPU variants (commercial variants)

HSP

050151

Heatspreader with 2.7 mm bore-hole standoffs for lidded CPU variants (industrial variants)

050152

Heatspreader with 2.7 mm bore-hole standoffs for bare-die CPU variants (commercial variants)

Note

1. We recommend a maximum torque of 0.4 Nm for carrier board mounting screws and 0.5 Nm for module mounting screws.

2. The gap pad material used on congatec heatspreaders may contain silicon oil that can seep out over time depending on the environmental

conditions it is subjected to. For more information about this subject, contact your local congatec sales representative and request the gap

pad material manufacturer’s specification.

Caution

1. The congatec heatspreaders/cooling solutions are tested only within the commercial temperature range of 0° to 60°C. Therefore, if your

application that features a congatec heatspreader/cooling solution operates outside this temperature range, ensure the correct operating

temperature of the module is maintained at all times. This may require additional cooling components for your final application’s thermal

solution.

2. For adequate heat dissipation, use the mounting holes on the cooling solution to attach it to the module. Apply thread-locking fluid

on the screws if the cooling solution is used in a high shock and/or vibration environment. To prevent the standoff from stripping or

cross-threading, use non-threaded carrier board standoffs to mount threaded cooling solutions.

3. For applications that require vertically-mounted cooling solution, use only coolers that secure the thermal stacks with fixing post. Without

the fixing post feature, the thermal stacks may move.

4. Do not exceed the recommended maximum torque. Doing so may damage the module or the carrier board, or both.

Содержание 050100

































































Результаты поиска

Содержание 050100

Отзывы:

Бренды по названию

Популярные бренды

Congatec 050100, Руководство пользователя

Результаты поиска

Содержание 050100

Отзывы:

Бренды по названию

Популярные бренды