Concoa 536 Series Скачать руководство пользователя страница 3

  

DESCRIPTION OF PRODUCT

..

   

The  536/537  Series  AutoSwitches  are  automatic  switchover  systems  designed  to  provide  a 
continuous supply of high purity gas. These units may be configured with or without the connections 
to connect to both high pressure and liquid cylinders. The primary bank (left side) of the AutoSwitch 
system is configured for use with liquid cylinders, pressure up to 600 PSI(41 bar). The reserve bank 
(right  side)  is  configured for  high  pressure  cylinders filled  up  to  3500  PSI  (241  bar). The  standard 
AutoSwitch  system  will  maintain  a  regulated  line  pressure  within  the  values  shown  in  the  table 
below:

 

 

MODEL

 

RANGE

 

536 2XXX

 

0-50 PSI  (0-3.5 BAR)

 

537 2XXX

 

0-50 PSI  (0-3.5 BAR)

 

536 3XXX

 

0-100 PSI  (0-7 BAR)

 

537 3XXX

 

0-100 PSI  (0-7 BAR)

 

 

The continuous working inlet pressure on the primary bank (liquid cylinder) must be above 140 PSI 
for the system to operate properly. When the primary bank falls below this value, gas will be pulled 
from the reserve side.

 

 

Models  of  these  AutoSwitches  are  available  with  or  without  pressure  switch  gauges.  Models  with 
pressure  switch  gauges  can  be  configured  for  use  in  conjunction  with  an  optional  remote  alarm. 
They cannot be connected directly to AC line voltage. Models with pressure switch gauges include 
a power indicator light and LED status lights to indicate the condition of the gas cylinders. A green 
indicator  light  signifies  a 

“Normal”  condition,  while  a  red  light  indicates  an  “Alarm”  (gas  cylinder 

empty) condition. The pressure switch AutoSwitch systems also include a strain relief on the bottom 
through which wiring can be connected to an internal circuit board and to a remote alarm such as 
CONCOA’s Altos 2 *.

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 1

 

  

INTENDED USE OF PRODUCT

   

The brass 536 Series AutoSwitch systems are intended for use in high purity, non-corrosive gas 
applications. The stainless steel 537 Series AutoSwitch systems are for use in ultra-high purity 
applications. Please note the safety information shown in the later sections.

 

-3-

 

Содержание 536 Series

















Отзывы: