82
83
EN
EN
VR3210 | VR3205
VR3210 | VR3205
the button in the centre of the tank and push it
horizontally along the back of the robot. The module
is installed in place when you hear a “click” sound
and a voice announcement from the appliance.
9. Removing the wiping module
Once the robot has completed its work, press the
latches on both sides, remove the wiping module
backwards, empty the water from the water tank and
clean the cloth (do not move or flip the robot during
cleaning).
Electrically operated water tank
10. Instructions for using the wiping module
•
Do not use the wiping module unless supervised.
•
For safety, make sure the wiping module is removed
when charging or when not in use.
•
Do not attempt to wipe the carpet.
•
For a better wiping effect, the wiping module should
be used after sweeping or vacuuming the floor three
times.
•
To refill water or clean the cloth while the appliance
is operating, pause it, remove and reinsert the wiping
module as described in steps 8 and 9. Do not move or
flip the appliance to avoid positioning errors and map
loss.
•
The wiping function of the appliance is designed for
wiping and aids deep cleaning. However, it cannot
effectively remove stubborn dirt and thus replace
human power.
•
We recommend soaking the wiping cloth before
mopping for better cleaning.
OPERATION
ON/OFF
Press and hold the button for 3 seconds, the indicator
light comes on and the appliance starts.
Press and hold the button for 3 seconds while the
appliance is in standby mode, the indicator light flashes
red and the appliance switches off.
NOTE: The appliance cannot be switched off while it is
being charged.
CLEANING/PAUSE
After starting the appliance, briefly press the button on
the appliance or start the appliance using the mobile app
(press any button to pause the appliance).
Note:
•
The robotic vacuum cleaner cannot be used to remove
fluids.
•
If the battery charge level is less than 15 %, the
appliance cannot operate. In this case, recharge it.
•
If the battery charge level is less than 15 %, the
appliance automatically returns to the docking station.
•
Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
robot catches these wires.
CHARGING
Automatic mode
: The appliance automatically returns to
the docking station after work.
Manual mode
: When paused, press the button briefly
to start charging or you can use your mobile app to
charge the appliance. The indicator light flashes when the
appliance is fully charged.
Note: If the appliance does not find the docking station,
it will automatically return to its original position. In this
case, place the device manually into the docking station.
COMPLETE AUTOMATIC CLEANING
Once the robot is on, it performs a search, generates
a map and intelligently divides it into areas. Then it sweeps
the areas one after the other properly, efficiently and
thoroughly along the wall and plans a curved / S-shaped
cleaning path. After cleaning, the robot automatically
returns to the charging base.
When mopping, the robotic vacuum cleaner starts
mopping in Y mopping mode. It moves in the shape of the
letter Y. You can switch to the normal U-shape movement
mode in the application.
Note
: Do not move the robot arbitrarily and often during
cleaning. After moving, place the robot in its original
position. When the robot is on again, it will try to take
a position itself. After successful positioning, the robot
will follow the planned path and continue working. If
positioning fails, the robot cancels the previous task,
creates a map, and cleans up again. Even if it does not find
a charging base.
LOCAL TURBO CLEANING
If a local area needs more thorough cleaning, the user
specifies an area of 1.5 x 1.5 m that he/she wants to clean
on the map. The appliance automatically moves to this
area and starts cleaning it. The appliance cleans the area
twice using the TURBO suction power.
LOCAL CLEANING
If you cannot control the robot using the mobile app,
move the robot manually to the place you want to clean
up. Press the button for 3 seconds and the robot will
perform double cleaning in the area of 2 x 2 m with the
centre in its starting position.
ZONE CLEANING
Use the mobile app to set the size and location of the area
you want to clean up. You can set up to 10 areas. The robot
will clean in the areas you have set.
RESTRICTED ZONE
Use the mobile app to set up one or more restricted areas.
The robot will not clean in these restricted areas and will
clean in others.
Note
: The robot may reach the restricted area due to
positioning errors, sensor errors or other reasons.
•
A permanently restricted zone may be invalidated due
to a significant change in position of the charging base
and furniture. Therefore, try not to move the robot or
otherwise interfere with its work during cleaning.
•
The permanently restricted area will be revoked as
soon as the map is restored.
CLEANING PLANNING
You can set a fixed cleaning time using the mobile app.
The appliance will automatically start cleaning at the
specified time and will return to the docking station when
completed.
WI-FI RESET
If the mobile phone cannot connect to the appliance due
to a change in router and password configuration or other
reasons, press the button and the button for 3 seconds
at the same time until you hear the “Wi-Fi lost, please follow
app instruction for reconnection” voice prompt and until the
indicator light turns on blue-violet and flashes slowly.
SILENT MODE
Robot voice messages and planned cleaning will be
suppressed (inactive) during the set time.
CARPET TURBO
When the carpet is detected, the suction force
automatically increases to the highest level.
WARNING -
the carpet is correctly detected only with the Carpet
brush. Do not use the Hardfloor brush to clean the
carpets.
SETTING THE SUCTION POWER
You can set the suction power to a low, standard or high
level using the mobile app.
The HARDFLOOR brush automatically detects dirt and
selects the appropriate suction power.
When the carpet is detected, the suction force
automatically increases to the highest level. WARNING
- the carpet is correctly detected only with the Carpet
brush.
WATER FLOW SETTING
You can set the water flow to a low, standard or high level
using the mobile app. The water flow cannot be changed
on the remote control. The flow will be set to standard.
Use the mobile application to set the water flow.
UV LAMP AND STERILIZATION
You can also control the UV lamp via the application. For
safety reasons, turn the lamp on only with the dust cup.
Do not turn on the lamp with the wiping module. During
sterilization, the vacuum cleaner shuts off the suction,
halves the speed of the movement and reduces the
rotation speed of the of the main brush and side brushes.
Y-WASH AND STANDARD WIPING
Y-wash wiping is set as the default.
When wiping
with the Y-wash function, the vacuuming must be
switched off. This prevents water from entering the
vacuum cleaner motor.
To change to standard wiping, connect to the mobile
application.
USING THE REMOTE CONTROL
1. Cleaning planning
2. Moving forward
3. Turning left
4. Local TURBO cleaning
5. Start/pause charging
6. Automatic cleaning / pause
7. Cleaning/pause
8. Turning right
9. Sterilization mode
10. Setting suction power
1
2
3
4
5
6
7
8
9
10
