Concept2 RK3190, Руководство пользователя

Страница: 19 / 45

36 37
RK3190 RK3190
EN EN
PRODUCT DESCRIPTION
1. Lid
2. Kettle body
3. Water mark
4. Button to open the lid
5. Carrying handle
6. Supply cable base
CAUTION:
Prior to first use, we recommend boiling the maximum volume of water in the kettle at least 3 times, then pouring it
out. The kettle is then ready for operation.
The kettle may only be used with the supplied base.
Description of the control panel
7. ON/OFF button
8. KEEP WARM button
9. Temperature setting buttons
OPERATING INSTRUCTIONS
1. Take the kettle off the stand (6), press the button (4) to open the lid (1) and fill the kettle with water (up to the
allowed maximum only) Close the lid by pushing onto it.
2. Place the kettle onto the stand (6) – the electrical contacts connect automatically. Thanks to the central connector
design, the kettle can turn around 360° and be put on the base from any side.
3. Connect the base to the mains. The ON/OFF is illuminated in green colour (7) and the 100°C temperature button is
illuminated in blue (flashing).
4. Turn the kettle on by pressing ON/OFF (7). The ON/OFF is illuminated in red colour (7) and the 100°C temperature
button is illuminated in blue (continuously). At the same time the blue light turns on.
5. The kettle will always boil the water to 100°C unless another programme is selected. After reaching the boiling
point, you hear an audible signal and the kettle switches off automatically. The light turn off.
Press the ON/OFF button (7) to end the heating process prematurely.
6. Temperature Selection
Press the button with preset temperature of 70°C, 80°C, 90°C, 100°C (9) to set the required heating temperature.
Confirm your selection by pressing the ON/OFF (7) button. The kettle starts heating the water up to the selected
temperature and the ON/OFF button illuminates in red. The selected temperature button (7) will be illuminated
in blue (continuously). Press the ON/OFF button (7) to end the heating process at any time. Upon reaching the
selected temperature, the kettle turns off automatically and the ON/OFF (7) button returns to the green state. You
can select from the following programmes:
70°C, 80°C, 90°C, 100°C or KEEP WARM (maintain the temperature).
The kettle automatically shuts off after reaching the set temperature (does not apply to the KEEP WARM programme).
7. KEEP WARM
Press the KEEP WARM button (8).
With this function selected, you can set the temperature to 70°C, 80°C, 90°C. Set the required temperature. Confirm
your selection by pressing the ON/OFF (7) button. The kettle starts operating. In case the kettle is taken off the
stand and put back on within 1 minute, the KEEP WARM function continues to maintain the preset temperature.
You can interrupt the KEEP WARM function by pressing the ON/OFF button (7) and subsequently turn it off by
pressing the KEEP WARM button (8). The kettle turns itself off automatically if not turned off with the ON/OFF
button within 2 hours.
Notice
If the ON/OFF button is illuminated in red colour, it means that the water is being heated or kept warm via the KEEP
WARM function.
8. Standby Mode
If no button is pressed on the stand of the kettle for 30 minutes, the kettle turns of automatically and so does the
illumination (the same applies even if the kettle is off the stand).
The kettle can be prepared for operation by pressing the ON/OFF key again.
Note : It is not a sign of a defect when a small amount of water droplets appear on the kettle base (6). It is a small
amount of condensed steam, which deactivates the kettle thermostat.
CLEANING AND MAINTENANCE
Warning!
Prior to each cleaning operation disconnect the lead-in cable of the appliance from
el. socket! Prior to start any handling operation, make sure that the appliance is
cooled down!
Use only a wet rag for cleaning surface of the appliance, do not use any cleansers
or hard things which could damage the surface!
Never clean the appliance under running water, never flush it and never
immerse the appliance into water!
3
6
5
2
7 8 9
1
4