Conair TrueBlend TB500-4 Скачать руководство пользователя

Страница: 99 / 150

TrueBlend

™

Operation

Edition: February 2007

Module number

(for service users only!)

(Level 3)

Input the module number of the control-

ler (default 249).

It must always match the last octet of the IP
address. After changing the IP address the
module is always automatically changed to
match the IP address. If it is changed later,
the controller must also be switched off and
on again.

Subnet mask

(for service users only!)

(Level 3)

Displays the current subnet mask of the con-
troller (all models).

7.17 System info

The software status of the TrueBlend and the firmware status if the touch panel
can be read in the system info

Read the software status, the version,

the date and the time here.

•

Software version:

Firmware version of the touch panel

•

Software label:

Description of firmware

•

Software date:

Creation date of firmware

•

Software time:

Creation time of firmware

Содержание TrueBlend TB500-4























































































































































Результаты поиска

Содержание TrueBlend TB500-4

Отзывы:

Похожие инструкции для TrueBlend TB500-4

Бренды по названию

Популярные бренды

Conair TrueBlend TB500-4, Руководство пользователя

Результаты поиска

Содержание TrueBlend TB500-4

Отзывы:

Похожие инструкции для TrueBlend TB500-4

Бренды по названию

Популярные бренды