42
COMUNELLO
®Copyright 2019 - All rights reserved
8.3 EXTENDED MENU 2
The control unit is factory set to allow direct selection exclusively of the main
menu functions.
If you wish to enable the functions described in
Extended Menu 2
,
proceed as follows:
• Select blinking LEV LED and press SET twice;
• Premere 2 volte SET;
• The LED will start blinking (alternate flashing of LED LEV
);
L1
BRAKE
CANNOT BE DISABLED
CANNOT BE DISABLED
L2
STEP BY STEP 1
ON
OFF
L3
ALWAYS CLOSE
ON
OFF
L4
FOLLOW ME
ON
OFF
L5
PEDESTRIAN TIME
ON
OFF
L6
2°CH MONOSTABLE
ON
OFF
L7
DISTANCE PROGRAM.
ON
OFF
LEV
MENÙ
2 FLASHES
In this way you will have 30 seconds to select the functions of Extended
Menu 2 by using the SELECT and SET keys; after a further 30 seconds the
control unit returns to the main menu.
8.3.1
LED L1
- BRAKE:
The control unit reduces the advancement of the gate caused by inertia, in
correspondence with a stop or inversion command.
8.3.2
LED L2
- STEP BY STEP 1:
Proceed as follows if you wish to enable the function “Step-by-step 1”:
• Make sure you have enabled the extended Menu 2 (as shown by the
alternate flashing 1 1 0 1 1 0 1 1 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L2;
• Press the SET key;
• LED L2 becomes steady on and programming will be completed.
Repeat the procedure if you wish to restore the previous configuration.
Important Note:
the Step by Step 1 function overwrites the standard
operation Step by Step logic and it can be enable only if a “Step-by-step”
in enabled and the “Pause time” period is stored.
8.3.3
LED L3
- ALWAYS CLOSE:
The control unit provides the facility to set “Always Close” operation: this
function, which is programmable only if a Pause Time has already been
programmed, is activated after a power failure; if the gate open condition
is confirmed a closing movement is started automatically, preceded by 5
seconds of pre-flashing.
Important note:
this command can be programmed only if a Pause Time
has already been set.
If you wish to enable the function, proceed as follows:
• Make sure you have enabled the extended Menu 2 (as shown by the
alternate flashing 1 1 0 1 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L3;
• Press the SET key;
• LED L3 becomes steady on and programming will be completed.
Repeat the procedure if you wish to restore the previous configuration.
8.3.4.
LED L4
- FOLLOW ME:
The control unit allows the “Follow me” function to be configured;
programmable only if a Pause Time has already been set, this function
reduces the Pause Time to 5 seconds after freeing the DS1 photocell,
meaning the gate re-closes 5 seconds after transit of the user.
Note:
this command is programmable only if a Pause Time has already
been programmed.
Proceed as follows if you wish to enable the function:
• Make sure you have enabled the extended Menu 2 (as shown by the
alternate flashing 1 1 0 1 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L4;
• Press the SET key;
• LED L4 becomes steady on and programming will be completed.
Repeat the procedure if you wish to restore the previous configuration.
8.3.5
LED L5
- PEDESTRIAN TIME:
Programming of the stroke of motor no.1:
The control unit is factory set with Pedestrian opening time (associated to
Motor no.1) of 10 seconds without any deceleration.
That time can be modified and decreased or increased up to 4 min. To
set a new pedestrian time programming must be carried out with the leaf
associated to Motor no.1 in closed position as follows:
• Make sure you have enabled the extended Menu 2 (as shown by the
alternate flashing 1 1 0 1 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L5;
• Press the SET key;
• Motor no.1 starts the opening phase;
• When the desired deceleration starting point is reached press the SET
key (the leaf continues its stroke at a decelerated speed);
• The L5 LED will start to flash more slowly and the Motor will decelerate;
• When the desired position is reached, press the SET button to end the
Opening cycle;
• The L5 LED will flash again normally and the motor will start Closing once more;
• Repeat the procedures described above for the Closing phase.
If you do not require the control unit to perform the deceleration, during
programming, when the opening and closing cycle has been completed
press the SET key twice consecutively rather than just once.
During programming, instead of the SET key on the control unit you can use
the button on the remote already stored.
8.3.6.
LED L6
- AUXILIARY RADIO CHANNEL OPERATING LOGIC:
The control unit allows the operating logic of the
Auxiliary Radio Channel
to be selected.
The control unit is factory set with
“Monostable”
operation of the Auxiliary
Radio Channel. If you wish to enable
“Bistable”
operation proceed as
follows:
• Make sure you have enabled the extended Menu 2 (as shown by the
alternate flashing 1 1 0 1 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L6;
• Press the SET key;
• LED L6 becomes steady on and programming will be completed.
8.3.7.
LED L7
- REMOTE RADIO CONTROL PROGRAMMING:
The control unit allows the transmission code to be programmed
remotely
without acting directly on the control unit SELECT key.
Remote programming of a Radio remote control is performed as follows:
• Send, continuously for a time in excess of 10 seconds, the code of a
previously saved remote control;
• the control unit thus enters programming mode as described in the main
menu (see sec. 9.1.2).
• If a previously saved pedestrian code is transmitted continuously the
control unit will enter programming mode of a new pedestrian code and
LED L2 will blink as though acquisition of the pedestrian code were
active (1 1 0 1 1 0 1 1 0);
• If the code is associated with the 2nd CH/AUX input the LED will blink as
though acquisition of the 2nd CH code were active (1 1 1 0 1 1 1 0 1 1 1 0).
To enable the remote programming function, proceed as follows:
• Make sure you have enabled the extended Menu 2 (as shown by the
alternate flashing 1 1 0 1 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L7;
• Press the SET key;
• LED L7 becomes steady on and programming will be completed.
Repeat the procedure if you wish to restore the initial configuration.
