Comtrend Corporation AR-5381u Скачать руководство пользователя страница 45

Страница: 45 / 206

To remove an entry, tick the corresponding checkbox



in the Remove column and

then click the

Remove Entries

button, as shown below.

Heading

Description

Enable RADVD

Enable use of router advertisement daemon

RA interval Min(sec):

Minimum time to send router advertisement

RA interval Max(sec):

Maximum time to send router advertisement

Reachable Time(ms):

The time, in milliseconds that a neighbor is
reachable after receiving reachability
confirmation

Default Preference:

Preference level associated with the default
router

MTU (bytes):

MTU value used in router advertisement
messages to insure that all nodes on a link use
the same MTU value

Enable Prefix Length Relay

Use prefix length receive from WAN interface

Enable Configuration Mode

Manually configure prefix, prefix length,
preferred lifetime and valid lifetime used in
router advertisement

Enable ULA Prefix Advertisement Allow RADVD to advertise Unique Local Address

Prefix

Randomly Generate

Use a Randomly Generated Prefix

Statically Configure Prefix

Specify the prefix to be used

Statically Configure

The prefix to be used

Preferred Life Time (hour)

The preferred life time for this prefix

Valid Life Time (hour)

The valid life time for this prefix

Enable MLD Snooping

Enable/disable IPv6 multicast forward to LAN
ports

Содержание AR-5381u















































































































































































































Результаты поиска

Содержание AR-5381u

Отзывы:

Похожие инструкции для AR-5381u

Бренды по названию

Популярные бренды

Comtrend Corporation AR-5381u, Руководство пользователя

Результаты поиска

Содержание AR-5381u

Отзывы:

Похожие инструкции для AR-5381u

Бренды по названию

Популярные бренды