Comtech EF Data SMS-7000 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 148

background image

SMS-7000 Modem Protection Switch

Installation

Rev. 3

2–15

2.4.1.1

SCU (J4) to DSU (J11) Interface

Refer to Figure 2-5.

Cable Assembly Part No. CA/5361 is provide with the switch. This is a single cable
interface between SCU Data Switch Interface J4 connector to the DSU Switch Controller
Interface J11 connector. The cable carries modem alarms, power supply faults, the serial
command link, and SCU power.

2.4.1.2 Remote

Connection

Refer to Figure 2-5.

Option - Cable Assembly Part No. CA/0755 is offered by Comtech EFData. The remote
serial interface J6 connector of each modem in the configuration is bussed to the SCU
Modem Remote J2 connector.

This cable is a 9-pin D EIA-485 2-wire ribbon cable and must be connected before
programming the switch configuration. The cable assembly is configured for:

•

Baud Rate: 9.6 to 19.2K

•

7 Information bits

•

Parity: Even

•

2 Stop bits

Note: Ensure the modems are all set to EIA-485 2-wire and that the baud rates match.

The ribbon cable assembly is used to query the configuration of modems, to set the
configuration of the backup modem, and to verify the saved configuration of the
modems. This data is used by the switch controller to set the position of the relays in the
data modules.

«
...
47
48
49
50
51
...
»

Содержание SMS-7000





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SMS-7000

Бренд: Patton electronics Страницы: 104

Бренд: Zektor Страницы: 17

Бренд: Xantech Страницы: 20

Бренд: Movie Vision Страницы: 2

Бренд: SMC Networks Страницы: 2

Бренд: Omega Engineering Страницы: 8

Бренд: Edge-Core Страницы: 9

Бренд: ATEN Страницы: 2

Бренд: PABX Страницы: 46

Бренд: LEGRAND Страницы: 4

Бренд: Penguin Computing Страницы: 71

Gigabit Switch 8

Бренд: 3Com Страницы: 2

Бренд: Shadow Страницы: 4

Бренд: Allied Telesis Страницы: 44

Бренд: StarTech.com Страницы: 2

Бренд: Kramer Страницы: 3

Бренд: N-Tron Страницы: 152

SuperStack II 3C16671A

Бренд: 3Com Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды