Comtech EF Data SMS-7000 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 148

background image

SMS-7000 Modem Protection Switch

Remote Control Operation

Rev. 3 Draft

A–11

A.4 Status

Commands/Responses

Backup
Modulator
Config.
Status

Command:
Response:

<add/MCS_Bn'cr'
>add/MCS_Bn'cr'
MA_xxx'cr'
ADD_mmm'cr'
SM_xxx'cr'
PMA_mmmmmmmm'cr'
MU_xxx'cr'
MUA_mmm'cr''lf']

(See Note)

Where: n = 1 or 2 (backup modem number).

Modulator Active (YES/NO)
Modem Address
Switching Mode (IND/DEP)
Prime Modem Assignments
Multiplexer Unit Attached (YES/NO)
Multiplexer Unit Address

The backup modulator configuration status command
causes a block of data to be returned by the SMS-7000. The
block of data reflects the stored configuration of the backup
modem selected.

Note: Status only returned if multiplexer unit attached.

Backup
Demodulato
r Config.
Status

Command:
Response:

<add/DCS_Bn'cr'
>add/DCS_Bn'cr'
DA_xxx'cr'
ADD_mmm'cr'
SM_xxx'cr'
PMA_mmmmmmmm'cr'
MU_xxx'cr'
MUA_mmm'cr''lf']

(See Note)

Where: n = 1 or 2 (backup modem number).

Demodulator Active (YES/NO)
Modem Address
Switching Mode (IND/DEP)
Prime Modem Assignments
Multiplexer Unit Attached (YES/NO)
Multiplexer Unit Address

The backup demodulator configuration status command
causes a block of data to be returned by the SMS-7000. The
block of data reflects the stored configuration of the backup
modem selected.

Note: Status only returned if multiplexer unit is attached.

Prime
Modulator
Config.
Status

Command:
Response:

<add/MCS_n'cr'
>add/MCS_n'cr'
MA_yyy'cr'
MP_y'cr'
MD_yyy.y'cr'
ADD_mmm'cr'
MU_xxx'cr'
MUA_mmm'cr'

(See Note)

DID_xxxxx'cr'
ECLK_xxxxx'cr'
IDI_xxxx'cr''lf']

Where: n = 1 to 8 (prime modem number).

Modulator Active (YES/NO)
Modulator/Modem Priority
Modulator/Modem Delay
Modem Address
Multiplexer Unit Attached (YES/NO)
Multiplexer Unit Address
Drop & Insert Data (BAL/UNBAL)
External Clock (BAL/UNBAL)
Insert Data Input (LOOP/NORM)

The prime modulator configuration status command causes
a block of data to be returned by the SMS-7000. The block
of data reflects the stored configuration of the prime modem
selected.

Note: Status only returned if multiplexer unit is attached.

«
...
125
126
127
128
129
...
»

Содержание SMS-7000





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SMS-7000

Бренд: Field Controls Страницы: 4

Бренд: Vector Страницы: 6

iMcV-Giga-FiberLinX-II

Бренд: IMC Networks Страницы: 60

Бренд: Elements Страницы: 2

Бренд: Kobold Страницы: 23

Бренд: QSFPTEK Страницы: 12

Enova DGX 100 Series

Бренд: AMX Страницы: 2

Бренд: Emulex Страницы: 75

Бренд: Cabletron Systems Страницы: 85

Бренд: InvoTek Страницы: 4

Бренд: Linksys Страницы: 22

Бренд: Black Box Страницы: 132

Бренд: xpr Страницы: 12

Бренд: Zigen Страницы: 72

NIVOMAG MK-21 Series

Бренд: NIVELCO Страницы: 2

Бренд: Shenzhen Kinan Technology Страницы: 27

Бренд: ZLINK Страницы: 44

Бренд: IDK Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды