Comtech EF Data MBT-5000 Скачать руководство пользователя страница 99

Страница: 99 / 138

MBT-5000 L-Band Up/Down Converter System

MN-MBT5000

Ethernet-based Remote Product Management

Revision 4

6–23

•

Valid Conv A/ConvB Forward RF Power readings are provided only if the pertinent

MBT-5000 up converter (BUC) is optionally configured with the Power Monitor feature.

These parameters otherwise will display as

N/A

if the pertinent converter is a BDC.

•

Valid Power Supply 2 and Local Switch Position information is provided with redundant

configurations only.

Firmware Information

This scrollable window identifies the Bootrom, Bulk Image#1 and Bulk Image #2.

Base Unit Part Number

The part number for the MBT-5000 chassis (i.e., the “base unit”) is identified here.

Converter A or B Part Number Type

These scrollable Part Number windows identify the part numbers for the converter modules

installed in the ‘A’ and ‘B’ slots.

Converter A or B Equipment Type

The scrollable Equipmen Type windows identify the function of each module slot (BUC or BDC)

along with the associated RF conversion band and frequencies.

Содержание MBT-5000










































































































































Результаты поиска

Содержание MBT-5000

Отзывы:

Похожие инструкции для MBT-5000

Бренды по названию

Популярные бренды

Comtech EF Data MBT-5000, Руководство пользователя по установке и эксплуатации

Результаты поиска

Содержание MBT-5000

Отзывы:

Похожие инструкции для MBT-5000

Бренды по названию

Популярные бренды