manualshive.com logo in svg

Comrex DH30, Руководство по эксплуатации продукта

Поделиться
Скачать
Comrex DH30 Скачать руководство пользователя страница 29

DH30 Product Manual

29

Status Outputs: 

Remotely check the status of the hybrid with the ON, OFF, CUE, 
REC, send presence and caller presence status outputs. All status 
outputs are open collector outputs rated at 40VDC and 50mA 
maximum.

MONITOR OUTPUT: 1/4” stereo jack

tip=+phase, ring=-phase, sleeve=-phase 
2W output into an 8 Ohm load

SEND INPUT: XLR female 

Mic/Line selectable, -55 or 0dBu nominal, adjustable, balanced 
bridging, 20k Ohm impedance, selectable 12VDC Phantom Power

CUE IN: XLR female 

Mic/Line selectable, -55 or 0dBu nominal, adjustable, balanced 
bridging, 20k Ohm impedance, selectable 12VDC Phantom Power

CALLER OUTPUT: XLR male 

0dBu nominal, adjustable, balanced 50k Ohm impedance 

AUX OUTPUT: XLR male 

0dBu nominal, adjustable, balanced 50k Ohm impedance 

TELCO LINE: RJ11 connector 

POTS (plain old telephone service) line or analog extension from a 
PBX or dry line (no DC offset voltage). A-Lead supervision provided 
(see “Line Connector” pinout chart on page 32 for further details).

TELCO SET: RJ11 connector 

A-Lead supervision provided (see “Set Connector” pinout chart on 
page 32 for further details).

All measurements referenced at –15dBm level on the phone line.

FREQUENCY RESPONSE: +/- 1dB from 250Hz to 3.5kHz
DYNAMIC RANGE: >70dB
DISTORTION: <0.15%

t

elePhone

 t

ranSmit

Содержание DH30












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды