manualshive.com logo in svg

Comrex DH30, Руководство по эксплуатации продукта

Поделиться
Скачать
Comrex DH30 Скачать руководство пользователя страница 10

Comrex Corporation

10

a

dditional

 c

onnectionS

Telephone Line Connections —

 The DH30 operates on one standard POTS 

(plain old telephone service) analog telephone line or one analog extension 
from a PBX via a standard RJ11C modular jack. 

Note: Some telephone lines 

do not provide battery voltage (dry line, no DC offset voltage). If your line 
does not, the DH30 may be configured by qualified personnel for dry line 
operation. Please contact Comrex technical support for details.

 

Line — 

Plug your telephone line into the 

rJ11C l

InE

 jack. 

 

Set —

 Plug your telephone set into the 

rJ11C S

Et

 jack.

Remote —

 Connect a DB25 parallel cable to this connector to provide con-

trol and status via your console remote port or contact-closure switches. This 
connector also contains unbalanced audio inputs and outputs. See “Pinouts” 
on pages 31-32.

Monitor — 

Connect a speaker or mono headphones to this 1/4” phone jack 

to produce a 2-watt amplified audio signal for call monitoring. Only caller 
audio is present on this output. Stereo headphones will contain caller audio 
in one earpiece only.

The front panel volume buttons control the level of this output. See the 
“Setup and Operation” section on pages 12-13 for front panel usage.

Record Control —

 Control a tape deck or other external recording device 

with this 

dB9 r

ECOrd

 C

OntrOl

 

connector.

This DB9 female connector sends start, stop and enable commands for au-
tomatic telephone call recording. This connector provides control only. Use 
the 

A

Ux

 O

Ut

 

connector to route audio to the recording device.

TELCO

LINE  SET

REMOTE

MONITOR

RECORD CONTROL

Содержание DH30












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды