Computec CDD6 Скачать руководство пользователя страница 16

Страница: 16 / 74

Computec

CDD6

CDD6: user manual – rev.07

Page 16/74

MLC interface connection

In case of replacement of different controllers with different plugs
proceed as following reported, otherwise plug the previous
connectors as they are.

Check the common voltage used, and the used contacts:

Common

Connections

Internal 24V_DD
(CDD6)

Check the presence of the 37-38 bridge as
GND reference

External 24V_EC
(MLC)

Remove the 37-38 bridge, only in case there
are no local contact installed on the car roof

For further information please refer to the paragraph 4.2.1

Connection of the MLC commands and of the local contacts:

PIN Name

X3.1 Pin Description

24V

Common 24V, available for MLC commands

DOC

Opening command

DCC

Closing command

RSC

Reduced speed command

RVC

Reversing command from detector

(FFC)

Door closed limit switch

PIN Name

X3.2 Pin Description

(AUXC)

Closing deceleration limit switch

(DTBC)

Opening deceleration limit switch

(EOC)

Door open limit switch

0V_IN

GND input for the photo-coupled inputs

0V_DD

Auxiliary GND of the door drive for the inputs

BUZS

Contact for Acoustic signal

For further information please refer to the paragraph 4.2.1

For any further information about magnetic switches application
(electrical connection, …) please refer to the related special
instruction

Power supply connection

Nominal Supply Voltage: [100 – 240]Vac [50-60]Hz, single phase
Range: [115-20%, 230+30%]Vac

Final Checks

Verify that required signals are connected,

then apply the cover

For further information please refer to the paragraph 4.2

- Table 7: installation of electrical parts (Magnet switch version)

–

Содержание CDD6











































































Результаты поиска

Содержание CDD6

Отзывы:

Computec CDD6, Руководство пользователя, Страница: 16 / 74

Результаты поиска

Содержание CDD6

Отзывы: