CommScope iP-600B-12-CSC-SMF Скачать руководство пользователя страница 5

Страница: 5 / 13

www.commscope.com

860106376

Issue 6, December 2012

Page 5 of 13

Step 3 – Installing the Shelf

When installing multiple shelves in a rack, install the lowest shelf first and work toward the top of the rack.

To install the shelf in the rack:

1. Mount the shelf in the rack using the four #12-24 x 3/8 inch screws provided (Figure 3).

Figure 3 Installing the Shelf in the Rack

2. Connect the panel bus jumper to the nearest connector on the panel bus (Figure 4).

Note:

The connector is keyed. The polarized tab on the jumper connector fits into the opening in the

header connector on the panel bus.

Important:

Make sure that the jumper connector is fully seated in the header connector on the panel

bus.

Figure 4 Connecting the Panel Bus Jumper to the Panel Bus

Mounting

screws (2)

Mounting

screws (2)

Panel bus jumper

Polarized tab

Panel bus

Содержание iP-600B-12-CSC-SMF














Результаты поиска

Содержание iP-600B-12-CSC-SMF

Отзывы:

Похожие инструкции для iP-600B-12-CSC-SMF

Бренды по названию

Популярные бренды

CommScope iP-600B-12-CSC-SMF, Инструкция

Результаты поиска

Содержание iP-600B-12-CSC-SMF

Отзывы:

Похожие инструкции для iP-600B-12-CSC-SMF

Бренды по названию

Популярные бренды