background image

 

SYSTIMAX

®

 Solutions                    

www.commscope.com

 

Instruction Sheet 860106376 

Issue 6, December 2012

 

 
 

SYSTIMAX

®

 iPatch

®

 600B Shelf with Faceplate Instructions 

 

 

 

 

© 2012 CommScope, Inc.  All rights reserved 

For RoHS Inquiries:
CommScope Inc.
Corke Abbey, Bray
Co. Dublin, Ireland
Attn: Legal Department

 

Page 1 of 13 

 

General 

The 

iPatch

®

  600B  shelf with faceplate is a 

SYSTIMAX

®

  approved product. This distribution shelf provides for 

connection of non-metallic Outside Plant (OSP) cable or Lightguide Building Cable (LGBC) to  12 

iPatch

  SC 

duplex fiber ports or 24 

iPatch

 LC duplex fiber ports either by direct termination or splicing. Designed for use in 

an 

iPatch

 system, this shelf is one unit high and can be mounted in a standard 19-inch rack with a universal hole 

pattern. This shelf slides out for easy access. 

Note:

  To use  the 

iPatch

  600B  shelf in an existing 

iPatch

  system, the network  manager and rack managers 

must be running software version 6.03 or later. The System Manager software, used to manage the system, 
must be Version 6.2 or later. We recommend that you upgrade the System Manager software to Version 6.2 or a 
later version before you install the  shelf. System Manager will automatically upgrade the 

iPatch

  Manager 

software. 

Ordering information is listed below:   
 

Material ID 

Part No. 

Description 

760005629

 

iP-600B-12-SC-MMF 

600B sliding multimode intelligent fiber shelf, SC 12 port duplex

 

760080895

 

iP-600B-12-CSC-SMF  600B sliding SC Single-mode intelligent fiber shelf, 12 port duplex 

 

How to Contact Us 

 

To find out more about 

CommScope

® 

 products, visit us on the web a

http://www.commscope.com/

 

 

For technical assistance: 

Within the United States, contact your local account representative or technical support at  
1-800-344-0223. Outside the United States, contact your local account representative or 
Authorized Business Partner. 

Within the United States, report any missing/damaged parts or any other issues to 
CommScope Customer Claims at 1-866-539-2795. Outside the United States, contact your 
local account representative or Authorized Business Partner. 

 

 

 

 

This product is covered by one or more of the following U.S. patents or their foreign equivalents: 6,285,293 and 6,522,737. 

Содержание iP-600B-12-CSC-SMF














Отзывы: