CommScope FlexWave Скачать руководство пользователя страница 5

Страница: 5 / 32

FWPP-504-02

FlexWave

Prism Remote Unit and RF Module Installation Guide

© May 2017 CommScope, Inc.

Page 1

O C U M E N T

V E R V I E W

This document provides the information you need to install a CommScope FlexWave

Prism Remote Unit (PRU).

Installation instructions are also provided for the following Prism Remote Unit RF Modules that reside in a PRU:

•

Single-Bay RF Modules, which includes the HDM and TDD RF Modules

•

Dual-Bay RF Modules, which includes the Dual-Band RF Modules and Legacy 40W RF Modules.

NOTE:

RF Modules are ordered separately and must be installed in a Prism Remote Unit in the field.

Table 1

lists the Prism Remote Unit chassis and

Table 2

through

Table 8 on page 3

list the Prism RF Modules that

this installation guide supports.

Table 1.

Supported FlexWave Prism Remote Unit Chassis

Catalog Number

Description

F P 1 - X X XX X X XX X X XR U

Single-Bay Prism Remote

F P 2 - X X XX X X XX X X XR U

Dual-Bay Prism Remote

F P 3 - X X XX X X XX X X XR U

Tri-Bay Prism Remote

F P 4 - X X XX X X XX X X XR U

Quad-Bay Prism Remote

Table 2.

Supported High-Density Module (HDM), Single Bay RF Modules

Catalog Number

Description

FWP-L4MT000MOD

20W Dual 700 Lower ABC, MIMO

FWP-L4MTU4MMOD

20W Dual 700 Lower ABC / 700 Upper C Non-Diversity

FWP-U4MT000MOD

20W 700 Upper C, MIMO

FWP-44MT000MOD

20W Dual 800 MIMO, with two External Filters

FWP-441T841MOD

20W Dual 800 SMR/ 1900 PCS, with 800 External Filter

FWP-C4MT000MOD

20W Dual 850 Cell/1900 PCS, Non-Diversity

FWP-B4MT000MOD

20W 850 MIMO

FWP-B410000MOD

20W 850 Wideband Cell, Non-Diversity

FWP-B810100MOD

40W 850 Wideband Cell, Non-Diversity

FWP-84MT000MOD

20W 1900 PCS MIMO, Non-Diversity

FWP-84MTA 4M MOD

20W Dual 1900 PCS/2100

FW P-Z4MT000MOD

20W 2100 AWS-3 MIMO

FWP-W4MT000MOD

20W 2300 WCS, MIMO

FWP-T4MT000MOD-L

20W 2500 TDD Low, MIMO, 2496.5-2571.5 MHz

FWP-T 4 S T0 0 0 M O D - H

20W 2500 TDD High, SISO, 2615-2690 MHz

FWP-A 4MT000MO D

20W 2100 AWS MIMO, Non-Diversity

FWP-A 4 1 60 0 0 M O D

20W 2100 AWS, Non-Diversity

FWP-A 8 1 T0 0 0 M O D

40W 2100 AWS SISO, Non-Diversity

FWP-8416000MOD

20W 1900 PCS SISO, Non-Diversity

FWP-881T000MOD

40W 1900 PCS SISO, Non-Diversity

Содержание FlexWave

































Результаты поиска

Содержание FlexWave

Отзывы:

Похожие инструкции для FlexWave

Бренды по названию

Популярные бренды

CommScope FlexWave, Руководство по установке

Результаты поиска

Содержание FlexWave

Отзывы:

Похожие инструкции для FlexWave

Бренды по названию

Популярные бренды