CommScope FlexWave Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 32

background image

Configuring the System with RF

FWPP-504-02

FlexWave

®

Prism Remote Unit and RF Module Installation Guide

© May 2017 CommScope, Inc.

Page 27

RF Module Cables and Supported Bay Installations for Legacy Dual-Bay

40W RF Modules

The cables and connectors have corresponding labels as shown in

Table 17 on page 28

for Legacy Dual-Bay 40W

RF Modules.

Table 17 on page 28

also shows which RF Module type can be installed in which PRU bay(s) when a

40W Dual-Bay RF Module is part of the RF Module mix in a PRU chassis. The Single-Bay chassis is not included in

Table 17 on page 28

.

For Dual-Bay installations, the RF cables and connectors are labeled as

MOD N TX0/RX0

and

MOD N TX1/RX1

,

where

N

refers to the top bay of the double-bay installation. For example:

•

For a Dual-Bay installation in a Quad-Bay chassis in which the RF Module is installed in the Bay D and Bay C
combination, the RF cables and connectors are labeled as

MOD D TX0/RX0

and

MOD D TX1/RX1

.

•

For a Dual-Bay installation in a Tri-Bay chassis in which the RF Module is installed in the Bay C and Bay B
combination, the RF cables and connectors are labeled as

MOD C TX0/RX0

and

MOD C TX1/RX1

.

Table 16.

Supported Bay Use and RF Antenna Labels for Single-Card, Dual-Card, and HDM RF Modules

(From Top of Remote Unit Chassis Down)

Supported Bay
Configurations
for Single-Bay RF
Modules

Supported Bay Combinations

for Dual-Bay RF Modules

RF Module Cable,
RF Module
Connector, and
Remote Antenna
Connector Label

Function

Supported
Bays in
Dual-Bay
Chassis

Supported
Bays in
Tri-Bay
Chassis

Supported
Bays in
Quad-Bay
Chassis

Bay D

MOD D

N/A

N/A

MOD D

Mod D TX0/RX0

Transmit RF power and primary/Path 1 receive
to/from the antenna for RF Module D

Mod D TX1/RX1

Transmit RF power and secondary/Path 2 receive
to/from the antenna for RF Module D

Bay C

MOD C

N/A

MOD C

Mod C TX0/RX0

Transmit RF power and primary/Path 1 receive
to/from the antenna for RF Module C

Mod C TX1/RX1

Diversity receive/Path 2 for Transmit RF power and
secondary/Path 2 receive to/from the antenna for
RF Module C

Bay B

MOD B

MOD B

MOD B

MOD B

Mod B TX0/RX0

Transmit RF power and primary/Path 1receive
to/from the antenna for RF Module B

Mod B TX1/RX1

Transmit RF power and secondary/Path 2 receive
to/from the antenna for RF Module B

Bay A

MOD A

Mod A TX0/RX0

Transmit RF power and primary/Path 1 receive
to/from the antenna for RF Module A

Mod A TX1/RX1

Transmit RF power and secondary/Path 2 receive
to/from the antenna for RF Module A

«
...
29
30
31
32
»

Содержание FlexWave

































Отзывы:

Нет отзывов

Похожие инструкции для FlexWave

Бренд: Aalborg Страницы: 128

Бренд: Warren Controls Страницы: 16

medialon Showmaster Go

Бренд: 7th Sense Страницы: 2

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Danfoss Страницы: 7

Бренд: Sanhua Страницы: 3

Бренд: Rabbit Страницы: 38

Бренд: Xilinx Страницы: 2

Бренд: Panasonic Страницы: 8

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: Insignia Страницы: 2

Бренд: I-Tork Страницы: 15

Бренд: MGC Страницы: 16

Бренд: Auber Страницы: 3

Бренд: Rabbit Страницы: 12

Бренд: Parallel Audio Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды