background image

 

3 HOMEDEPOT.COM

 

 

Please contact 1-877-527-0313 for further assistance.

READ AND SAVE THE ENTIRE MANUAL BEFORE OPERATING THE FAN.

Ensure that all safety practices and instructions are followed during the installation, operation and servicing of the fan. Failure to apply 
these safety practices could result in death or serious injury. If you do not understand the instructions please call the Commercial Electric 
Customer Service.
The fan installation should follow the recommendations outlined in this manual. Commercial Electric is not responsible for any injury or 
damage to people or property as a result of the user and/or installer not complying with the recommendations outlined in this manual.
All fan controls and incoming power should only be installed by qualified technicians familiar with the requirements of the National 
Electric Code (NEC) and local codes. Refer to appropriate portions of this manual for other important requirements. Failure to follow these 
guidelines will void the manufacturer’s warranty.
Installation is to be in accordance with the national electrical code, ANSI/NFPA 70-1999 and local codes.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of 
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible 
for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

• Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. 
• Before servicing or cleaning the unit, switch power off at the service panel and lock the service disconnecting means to prevent power 
from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, 
such as a tag, to the service panel.

WARNING: IF UNUSUAL OSCILLATING 
MOVEMENT IS OBSERVED, IMMEDIATELY 
STOP USING THE CEILING FAN AND CONTACT 
THE MANUFACTURER, ITS SERVICE AGENT OR 
SUITABLY QUALIFIED PERSONS. 

WARNING: MAKE SURE TO POWER THE FAN 
OFF AND LOCK IT OUT USING THE IEC/CE 
APPROVED DISCONNECT WHEN DOING ANY 
CLEANING AND OR MAINTENANCE TO THE 
EQUIPMENT.

PRIOR TO THE INSTALLATION, ENSURE:

• That the mounting of the suspension system shall be performed by the manufacturer, its service agent or suitably qualified persons; 

• That the fan is to be installed so that the blades are more than 10ft [3.05m] above the floor; 

• That all other installation and spacing requirements are met.
 

WARNING: DO NOT OPERATE OR INSTALL ANY 
FANS OR FAN ACCESSORIES THAT APPEAR 
TO BE DAMAGED. FAILURE TO FOLLOW 
THIS INSTRUCTION CAN RESULT IN DEATH, 
SERIOUS INJURY, OR EQUIPMENT DAMAGE.

Safety Information

Содержание 3055 50 157























Отзывы: