Comet T3110 Скачать руководство пользователя страница 4

 
 

 

 

 

4

 

 

IE-SNC-T3110-09

 

General description 

 

The  transmitters  T3110  are  designed  for  measurement  of  ambient 
temperature  and  relative  humidity  of  air  without  aggressive  substances. 
Measured  values  are  converted  to  other  humidity  interpretation:  dew  point 
temperature,  absolute  humidity,  specific  humidity,  mixing  ratio,  specific 
enthalpy. 

Measured  and  computed  values  are  displayed  on  a  two-line  LCD  display. 
The first line displays temperature 

(ºC / ºF). Value displayed on the second 

line  is  selectable  among  relative  humidity  and  computed  value.  It  is  also 
possible to display both readings with cyclic overwriting (4 seconds interval) 
or to switch off the LCD display at all.  

The transmitter communicates by means two galvanically separated current 
loop  4-20mA.  Each  loop  has  two-wire  connection  and  each  loop  requires 
power  from  evaluation  device.  It  is  always  necessary  to  connect    loop  I1 
which is designed for supplying of measuring part of the device. Using the 
configuration software can be assigned to each current loop any measured 
or computed value. 

All  transmitter  setting  is performed  by  means  of the  PC  connected  via  the 
optional  SP003  communication  cable  (not  included  in  delivery).  Using 
TSensor  software  (see 

www.cometsystem.com

)  you  can  assign  to  each 

output any measured or computed value and to set its measuring range. It is 
also possible to assign both outputs to the same value (with the same range), 
if two evaluation devices are necessary to connect. The program supports 
make the adjustment of the device too. This procedure is described at file 

Calibration manual.pdf

“ which is installed commonly with the software. 

 

Device versions: 

T3110 

transmitter with cable gland for output cable connection    

T3110L 

device  version  with  watertight  male  connector  instead  of  a 
cable  gland  for  easy  connection/disconnection  of  the  output 
cable (protection IP67)  

T3110Ex 

intrinsically  safe  transmitter  for  use  in  potentially  explosive 
environments  

T3110Z

 

this  marking  is  intended  for  a  non-standard  versions  of  the 
transmitters. Description is not included in this manual.  

 

Содержание T3110



















Отзывы: