manualshive.com logo in svg

CombiLift C2500CB, Руководство пользователя

Приобретите грузоподъемник CombiLift C2500CB и получите бесплатное руководство пользователя. Загрузите его с нашего сайта manualshive.com и начните использовать свой грузоподъемник с легкостью. Это надежное решение для вашего бизнеса.

Поделиться
Скачать
background image

 

     

 

 

 

 

 

      Maintenance 

 

 

 

96 

C2500CB-OM-EN-16 

Note 

Use of hydraulic oil that does not meet the required grade or temperature 

range may cause poor operation, reduced efficiency and/or damage to 

hydraulic components.  

Combilift trucks are supplied with ISO Grade 46 hydraulic fluid unless 

otherwise stated. Refer to the decal on the hydraulic tank. Please check if 

the hydraulic fluid is suitable for the trucks operating temperature range. 

Note 

Clean and dry the area around all components concerned thoroughly. 

Observe safety regulations when handling oils and avoid skin contact. 

Do not pour fluids into the ground, down a drain or into a stream, pond or 

lake. Observe relevant environmental protection regulations when disposing 

of used oil and filters.

 

6.13  Hydraulic Oil System 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Hydraulic Oil 

The  hydraulic  oil  must  be  changed  at  regular  intervals  in  accordance  with  the 
maintenance schedule. 
The  hydraulic  oil  used  in  the  trucks  hydraulic  system  must  conform  to 

ISO  3448

 

viscosity classification grade and include additives for improved: 

  Viscosity index 

  Wear prevention 

  Corrosion protection 

  Stability against oxidation 

  Deaerating and foam suppressing 

  Compatibility with seals and gaskets 

  Low pour point 

 
The oil must also have the correct temperature range for the operating temperature of 
the truck. If the operating temperature is outside the range of the standard grade 46 
oil, the standard oil should be replaced with the appropriate grade of oil.   

 

The  correct  grade  of  oil  for  the  relevant  operating  temperature  range  can  be 
determined using the following table: 

     

Caution   

 

Switch off the engine before working on the hydraulic system. 

Wait until the engine and hydraulic tank are cool enough to touch before 

commencing work. 

Содержание C2500CB
































































































































Отзывы:

Нет отзывов

Похожие инструкции для C2500CB

Hyundai 20D-7E Service Manual preview
20D-7E
Бренд: Hyundai Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды