background image

 

     

 

 

 

 

 

           Operation 

 
 

 

 

67 

C2500CB-OM-EN-16 

5.18  Driving on Slopes 

 

Always take great care when driving on a slope as the risk of an accident is increased. 
If a slope is greater than 5% the following guidelines must be followed. 

 

Do: 

  Drive slowly and use the brakes gently. 

  Drive directly up or down the slope in standard mode. 

  Ensure the 

forks face

 

uphill

 when driving up or down a slope 

with a load

  Ideally the 

forks should face

 

downhill

 when driving up or down a slope 

without a load

  Keep the mast tilted back and the forks approximately 100mm (4˝) off the 

ground. 

  Raise the forks at the bottom of a slope to prevent them from fouling the 

ground if necessary. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Driving in this way aids stability, traction and adhesion (meaning the truck is less likely 
to tip over or skid). If it is not possible to drive up and down the incline with the forks 
positioned as above then take great care and use additional means to secure the load 
such as ratchet straps if necessary. 
 
 
 
 
 
 

With Load 

Without Load 

Содержание C2500CB
































































































































Отзывы: