manualshive.com logo in svg

CombiLift C2500CB, Руководство пользователя

Поделиться
Скачать
CombiLift C2500CB Скачать руководство пользователя страница 110

 

     

 

 

 

 

 

      Maintenance 

 

 

 

109 

C2500CB-OM-EN-16 

Note 

Optional attachments with moving parts may have additional grease points 

that have not been indicated on the above chart. 

 

Grease points on attachments must be located and greased every 100 

HOURS using EP2 grease. 

Load Testing Forks 

A fork that has undergone repairs - other than repair or replacement of the positioning 
lock or marking - must be load tested before it is returned to service. The test load must 
correspond to 2.5 times the rated capacity marked on the fork. 
 

6.16  Grease Point Chart  

The diagram below indicates all of the points on the Combilift that must be greased 
regularly. A copy of this diagram is located in the operator compartment in the form of 
a decal / Information sticker. All Points must be greased every 

100 HOURS / 2 months

 

with EP2 grease. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

1. RH Swivel Slew 1 
2. RH Swivel Slew 2 
3. RH Steering Cylinder Front 
4. RH Steering Cylinder Back  
5. Rear Steering Cylinder Back 
 
* If fitted 

6. Rear Swivel Slew 1 
7. Rear Swivel Slew 2 
8. Rear Steering Cylinder Front 
9. LH Steering Cylinder Back  
10. LH Steering Cylinder Front 

 

11. LH Swivel Slew 1 
12. LH Swivel Slew 2 
13. LH Fork Positioning Cylinder * 
14. Tilt Cylinder Front 
15. Tilt Cylinder Back 
16. RH Fork Positioning Cylinder * 

6

7

8

9

10

11

12

13

14

15

16

1

2

3

4

5

Содержание C2500CB
































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды