CombiLift C2500CB страница 54 Скачать руководство пользователя | Manualshive

Страница: 54 / 127

background image

Operation

53

C2500CB-OM-EN-16

Caution

Moving the 4-way direction control lever when the truck is moving may

cause the truck to change direction abruptly and carries a risk of personal

injury and machine damage.

Do not move the 4-way direction lever when the truck is moving.

After changing direction with the truck stopped, confirm that the direction

indicator icon on the dash cluster is in agreement with the intended

direction selected.

If the direction control does not respond or the correct mode indicator does

not illuminate park the truck in a safe location and inform the relevant

supervisor.

Warning

Only operate the truck from the operator’s seat with the seat belt buckled. If

a door is fitted to the operating enclosure it must be closed and latched

securely. Do not place any part of the body outside the operating enclosure.

Do not carry passengers. Failure to follow these guidelines can result in

serious injury or death.

Warning

Remain in the seat with the seat belt fastened while the truck is moving. The

seatbelt will help you remain inside the cabin should the truck tip over.

Never jump from the truck if it begins to tip over. Keep all body parts inside

the operating enclosure.

Note

Allow the diesel engine to idle for 5 minutes before shutting it off after a full

load operation. Failure to do so may lead to turbocharger trouble.

5.9

Switching Off the Engine



Ensure the park brake is applied and the 4-way direction control lever is in the

neutral position.



Ensure the accelerator pedal is not being pressed.



Turn the key anticlockwise to position 0.

5.10 Moving Off

It is important to be aware of how the Combilift truck moves and how to drive it in a
safe and efficient manner. The Combilift can be driven forward, backward, left or right
by selecting the desired direction of travel with the 4-way direction control lever.

«
...
52
53
54
55
56
...
»

Содержание C2500CB
































































































































Отзывы:

Нет отзывов

Похожие инструкции для C2500CB

Бренд: ep Страницы: 49

Бренд: Rice Lake Страницы: 97

Бренд: Jungheinrich Страницы: 27

Бренд: Jungheinrich Страницы: 55

AMX 10 Inox Pro Ex

Бренд: Jungheinrich Страницы: 45

Бренд: Jungheinrich Страницы: 65

Бренд: Jungheinrich Страницы: 99

Бренд: Jungheinrich Страницы: 73

Бренд: Jungheinrich Страницы: 81

Бренд: Jungheinrich Страницы: 99

Бренд: Jungheinrich Страницы: 79

Бренд: Jungheinrich Страницы: 87

Бренд: Jungheinrich Страницы: 227

Бренд: Jungheinrich Страницы: 226

Бренд: Jungheinrich Страницы: 243

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды