Combi AuraStar, Инструкция по эксплуатации

Страница: 35 / 40

Trouble shooting
疑是產品故障時
34
When such conditions happens
The Intelligent Auto-Brake is not
started and the AuraBeam is not lit
even if the Intelligent Auto-Brake
or the AuraBeam button is pressed.
The Main battery level indicator is
not lit.
The Main battery
switch is not turned on
The Main battery
switch is not turned on
① Check whether the Main battery switch is turned
to “ON”. If not, set it to “ON”.
② Confirm that there is no foreign matter attached
to the USB charging cable connector and the
charging cable is not deformed. After charging
the Main battery, set the Main battery switch to
"ON".
The Main battery is
not charged
The Main battery
capacity is exhausted
The Main battery is
not correctly installed
No dry cell is loaded
The dry cell battery
capacity is exhausted
The Main battery and
the handle are not
paired
The Intelligent Auto-Brake button
blinks in blue.
The Intelligent Auto-Brake button
blinks in blue for 30 seconds
and then lights in red.
The AuraBeam button blinks in
blue constantly.
Possible cause Check and treatment
當出現這種狀況時 推測原因 確認及處理
Any foreign
substance
adheres to the
contact part of the
Main battery
Any foreign
substance adheres
to the contact part
of the Main battery
① Check whether the Main battery switch is turned
to “ON”. If not, set it to “ON”.
② Charge the Main battery.
③ Check the connection between the Main battery and
the stroller, and make sure that the Main battery is
loaded correctly.
④ Load the dry cell into the battery compartment
of the handle.
⑤ Replace the dry cell in the battery compartment
of the handle.
The Main battery and the handle must be paired.
Please follow the instructions in "Pairing and
unpairing the Main battery with the handle" on
page 30 of this manual.
Make sure that no foreign substance adheres to the
contact part of the Main battery. If there is any,
remove it completely.
Make sure that no foreign substance adheres to the
contact part of the Main battery. If there is any,
remove it completely.
主控模塊的剩餘電量指示燈不亮。
1
2
3
4
5
即使按下自動刹車或前燈鍵，也
不啟動、不亮燈。
自動刹車按鈕呈藍色閃爍。
自動刹車按鈕呈藍色閃爍 30 秒
後，呈紅色點亮。
前燈鍵一直呈藍色閃爍。
主控模塊與把手未配
對
主控模塊的接觸部分
附著有異物
主控模塊的接觸部分
附著有異物
主控模塊與把手必須配對，所以請按照本書第 30 頁
中記載的“主控模塊與把手配對及解除配對”進行操作。
確認主控模塊的接觸部分沒有異物附著，如果有異物
附著，應將異物清掃乾淨。
確認主控模塊的接觸部分沒有異物附著。如果有異物
附著，應將異物清掃乾淨。
主控模塊開關未開啟 ① 檢查主控模塊開關是否處於“ON”狀態，並將其設
為“ON” 。
② 確認 USB 充電線的連接器上無異物附著、充電線
無變形，給主控模塊充電後，將主控模塊開關撥
至“ON” 。
① 檢查主控模塊開關是否處於“ON”狀態，並將其設
為“ON” 。
② 給主控模塊充電。
③ 確認主控模塊與嬰兒手推車之間的連接狀態，並正確
安裝。
主控模塊未充電
主控模塊開關未開啟
主控模塊電量用盡
主控模塊未正確連接
未安裝乾電池
乾電池的電量用盡
④ 將乾電池裝入把手的電池倉中。
⑤ 更換把手主控模塊倉中的乾電池。
轉下頁
To be continued