ComAp IA-NT PWR Скачать руководство пользователя | Manualshive

Страница: 62 / 69

background image

InteliATS

NT

PWR, SW version 1.0, ©ComAp – March 2009

62

IA-NT- PWR-1.0-Reference Guide R1.pdf

IL-NT-RD Remote display software

This chapter describes Remote display software IL-NT-RD, which is designed as an remote signalling
and control software for InteliATS

NT

, InteliLite

NT

and InteliDrive Lite controllers.

It is the optional

software which is possible to upload into controller instead of standard controller’s firmware.

General description

Remote display software works as “remote display and control” for the master InteliATS

NT

, InteliLite

NT

or InteliDrive Lite controller. Genset/Engines can be controlled from remote display as well as from
master controller. All remote display screens (Measure, Setpoints and History) displays the same data
like master controller. Front panel buttons on both controllers work the same way. All remote display
LED’s shows the same state as corresponding LED’s on master controller.

Warning!

It is highly recommended to use the same type and model of controller for master and remote
display. Only in such case is assured the proper function of all buttons, LED diods and display.
Another combinations of HW types and models from Master controller and remote display are
not supported nor tested!

IL-NT-RD Software installation

The IL-NT-RD remote display firmware is installed in the same way as any other IA-NT firmware using
LiteEdit software. Please see LiteEdit Reference guide for details about upgrading firmware. IL-NT-RD
contains only firmware, not an archive.

However when there is IL-NT-RD firmware installed in the controller the procedure to install back the
original standard firmware is following:

•

Open any type of online connection.

•

DDE server will try to open the connection, but it will fail and write red error message in the

status bar.

•

At this moment go to

C

ONTROLLER

->

P

ROGRAMMING AND CLONING

->

P

ROGRAMMING

and select

proper!

firmware you want program to the controller. Choosing the wrong type of firmware

may result in non-functional controller.

•

Press "OK" button to programm the firmware to the controller.

«
...
60
61
62
63
64
...
»

Содержание IA-NT PWR






































































Отзывы:

Нет отзывов

Похожие инструкции для IA-NT PWR

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: Hama Страницы: 8

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Icom Страницы: 30

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ray Страницы: 11

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренд: JENCO Страницы: 36

Бренд: jcm-tech Страницы: 8

Бренд: FUTABA Страницы: 8

Бренд: Click2Enter Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды