Automatic Scrubber
RA 35
B, K 10
24
The 'C' LED (Fig. 4) lights up on the charger when the battery charge level is getting too low. The brush motor and the
suction motor are switched off automatically. The battery must be recharged as soon as possible.
To bring the machine to the recharging point, lift up the front of the machine and push it on the wheels.
5.2 Overflow Device
The machine has a filter which switches off the suction motor whenever the recovery tank is full.
In this case the tank must be emptied.
5.3 Traction
The machine traction is achieved by the brush working at a slight inclination, thus moving the machine forwards.
To move the machine backwards, lift up the floor-wiper.
6
After finishing work
When you finish work, before performing any type of maintenance proceed as follows:
1. Turn off the brush motor switch (Fig. 8A).
2. Turn off the suction motor switch (Fig. 8B).
3. Take the machine to the emptying site.
4. Empty the recovery tank
Always wear gloves when doing this to prevent contact with hazardous solutions.
5. Clean the floor-wiper using a jet of clean water. The floor-wiper must be raised when the machine is not in use to prevent
permanent deformation of the rubber strips.
6. Remove the brush and clean it with a jet of water
7
Daily maintenance
7.1 Cleaning the recovery tank
Always wear gloves when doing this to prevent contact with hazardous solutions.
1. Remove the protection cover after taking off the black plastic hoses.
2. Remove and carefully rinse the filter and the float (Fig. 11)
3. Lift the recovery tank, rotate it anti-clockwise and take it off (Fig. 12)
4. Rinse the recovery tank (Fig. 13), rinse and carefully clean the drain plug.
5. Replace everything by carrying out the procedure in reverse order.
To dispose of the liquids used for floor cleaning, follow the instructions and recommendations on the label and be sure
you comply with current legal requirements.
7.2 Cleaning the floor-wiper
Clean the floor-wiper with a jet of water. Check the condition of the rubbers and reverse or replace them as necessary. Careful
cleaning of the entire suction unit ensures a longer working life for the suction motor.
Clean the wiper hose and make sure it is not clogged (Fig. 10B).
7.3 Cleaning the solution tank filter
1. Remove and clean the filter.
2. Replace the filter.
3.
7.4 Removing the disk brushes
1. Raise the floor-wiper by moving the appropriate lever upwards
2. Raise the machine by pressing down on the handle
3. Press the start button several times
The brush is automatically released.
Содержание RA 3 K 10
