MAINTENANCE
Your spa will require additional air to be added from time
to time. Changes in temperature from day to night will
change the pressure in the spa and may cause a certain
amount of deflation. Please follow the Assembly
instructions and drain the spa before inflating to the
accurate pressure needed.
CAUTION: YOU MUST ENSURE THE PUMP IS
UNPLUGGED BEFORE BEGINNING SPA MAINTENANCE
TO AVOID RISK OF INJURY OR DEATH.
P04674
Filter Set
90352E
Filter Cartridge
Alarms
Solutions
Causes
Reasons
The water flow sensors
work without pressing the
filter or heat button.
1. The water flow sensor flags didn’t fall back
into the correct position.
2. The water flow sensors are broken.
1. Unplug the plug gently, strike the side of the pump (but not violently), and
plug it back in.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
After starting or during the
functions of filtering or/and
heating, the water flow
sensors do not detect
water flow.
1. You forgot to remove the 3 stopper caps from
inside the pool.
2. Filter cartridges are dirty.
3. Activate the filter or heat system and put your
hand in front of the outlet pipe inside the pool to
check if you can feel water flowing out.
a. If no water flows out the water pump is broken.
b. Water flows out but the alarm appears,
the water flow sensors are broken.
4. Filter blockage
5. Bent pipes or poor water flow through the
plasticpipes of the liner
6. Debris screens are blocked: debris screens can
become blocked by hard water due to calcium
build-up.
7. Perished washers
The washers within the spa couplings may have
become perished or worn.
1. Remove the 2 stopper caps before heating, refer to Assembly section in the
User’s Manual.
2. Remove the filter set from inside the pool and push the filter or heat button. If
no alarm appears, clean or change the filter cartridges install the filter set
inside the pool.
3. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
4. Clean the filter and check for damage. Replace or re-install as necessary.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
5. Please check through the spa connection to see if the pipes are bending.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
6. Empty the spa and place a garden hose inside the pipes to wash the debris.
To be sure all debris is removed, perform the operation from the outside and
inside of the spa.
Use a toothbrush to remove any stubborn debris.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
7. Check the washers inside the coupling for damage. Unscrew the couplings
and remove the washer for further inspection.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The thermal cut-out cut
off.
1. The ambient temperature is over 50°C (122°F) or
the pump is directly under the sunshine.
2. The thermal cut-out is broken.
1. Unplug the pump, and put the pump in a dry, cool place. Only re-start the
pump when the water temperature reaches 34°C (93.2°F) or lower.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer
connections have issues.
1. The pump’s thermometer connectors don’t
work properly.
2. The pump’s thermometer is broken.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer
reads the water
temperature below
4°C (40°F).
1. The water temperature is lower than
4°C (40°F)
2. If the water temperature is higher than
7°C (44.6°F), the pump’s thermometer is broken.
1. The spa is not designed to operate with water temperatures lower than
4ºC (40°F). Unplug the pump and only re-start the pump when the water
temperature reaches 6°C (43°F).
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer
reads the water
temperature over
48°C (119°F).
1. The water temperature is over 48°C (119°F)
2. If the water temperature is lower than
45°C (113°F), the pump’s thermometer is
broken.
1. The spa is not designed to operate with water temperatures greater than
40°C (104°F). Unplug the pump and only re-start the pump when the water temperature
reaches 38°C (100°F) or lower.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
Filter Cartridge Maintenance
NOTE:
To ensure your spa water stays clean,
check and clean your filter cartridges
every day follow the steps below.
12
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
