background image

Page 2 of 12

Standard Features

The H

2

Covert system offers the following features:

Primary Tones:  Wail, Yelp, Hi-Lo, Hyper-Yelp, Hyper-Lo, Whoop, Manual Wail, Air Horn

Vehicle Light Control Buttons – 7 levels:  3 Progressive, Auxiliary

PA with Built-In Noise Cancelling Microphone

Integrated Volume Control

Radio rebroadcast

- Stand-By 

Siren Scroll

Park Kill

Horn Ring Transfer

EU Lock

Backlit Buttons with On/Off Color Change

Three (3) Backlight Dimming Levels and Backlight Off Option

Two (2) Push Button Programmable Siren Controls

Two (2) Programmable Air Horn Pitch Controls

Externally accessible fuses

25’ Extension Cable

Unpacking & Pre-Installation

After unpacking the siren, carefully inspect the unit and associated parts for any damage that may have been caused in transit.  Report any 

damage to the carrier immediately.

Parts included in the box:

Siren (amplifier)

Hand-Held Controller with Base

25’ Extension Cable

Parts Bag

Installation & Mounting

The hand-held controller may be mounted in various locations in the vehicle:  below the dash, on the tunnel, etc. using the hardware supplied.  

Ease of operation and convenience to the operator should be the prime consideration when mounting the siren and controls.  The amplifier 

may be mounted at an appropriate location within the vehicle, and the 25’ extension cord can be used to couple the hand-held controller to the 

amplifier.

WARNING!

All devices should be mounted in accordance with the manufacturer’s instructions and securely fastened to vehicle elements of suf-

ficient strength to withstand the forces applied to the device. Ease of operation and convenience to the operator should be the prime 

consideration when mounting the siren and controls. Adjust the mounting angle to allow maximum operator visibility. Do not mount 

the Hand-Held Controller in a location that will obstruct the drivers view. Mount the Hand-Held Controller mounting base in a convenient loca-

tion to allow the operator easy access. Devices should be mounted only in locations that conform to their SAE identification code as described 

in SAE Standard J1849. For example, electronics designed for interior mounting should not be placed underhood, etc. Controls should be 

placed within convenient reach* of the driver or if intended for two person operation the driver and/or passenger. In some vehicles, multiple 

control switches and/or using methods such as “horn ring transfer” which utilizes the vehicle horn switch to toggle between siren tones may be 

necessary for convenient operation from two positions.

*Convenient reach is defined as the ability of the operator of the siren system to manipulate the controls from their normal driving/riding posi-

tion without excessive movement away from the seat back or loss of eye contact with the roadway.

The H

2

Covert amplifier is not waterproof. It must be mounted in a location that is sheltered from rain, snow, standing water, etc. It must be also 

installed in an adequately ventilated area. Do not install near heater ducts or under the vehicle’s hood.  Using the mounting holes on the ampli-

fier as a template, scribe four drill position marks at the mounting locations. Be sure that both sides of the mounting surface are clear of parts 

that may be damaged.  The siren accessory kit with mounting hardware supplied provides the user with a choice of mounting hardware. Secure 

the H

2

Covert amplifier to the mounting surface, using the mounting hardware, including lock washers.

Connection between the hand-held controller and the H

2

Covert amplifier box is an RJ45 connector.

Содержание H2 Covert













Отзывы: