Cobra 4600 CAN, Руководство по установке

Страница: 6 / 20

INSTALLATION MANUAL 4600 CAN/PLIP
6
Antennas.
The RF antennas positioning (for both the main unit and the siren) is crucial for a proper system’s performance . They
must not be cut, wrapped, connected to any other cables or to the vehicle body and they must be kept separate from
the main wiring harness and as far as possible from metallic parts.
Electrical connections.
WARNING : Disconnect the negative lead from the battery before continuing with the installation.
Pay attention when joining two or more wires. Avoid to make “quick connections” that do not ensure a good quality.
Also make sure that the wires of the Cobra 4600 are routed so that they follow the original wiring of the vehicle to which
they should be joined with the raps.
The addition of fuse is required as speci fi ed in the main connection diagram.
26 ways connector J pin-out for CAN con fi gurations
J-1 and J-2 Engine crank inhibition : to get the maximum security level to the system connect the two wires as shown
in the electrical diagrams to prevent the engine starter running. During the cranking phase, measure the value of the current in the circuit
that has been interrupt, to make sure that it does not exceed the technical speci fi cations of the product. Install an additional relay if required.
J-3 Logic blinker output : make the connection if required by the speci fi c vehicle CAN installation sheet.
J-4 Power blinker output : make the connection if required by the speci fi c vehicle CAN installation sheet.
J-5 Logic blinker feedback input or power blinker output :
make the connection if required by the speci fi c
vehicle CAN installation sheet.
J-6 analogic input
: make the connection if required by the speci fi c vehicle CAN installation sheet.
J-7 analogic input
: make the connection if required by the speci fi c vehicle CAN installation sheet.
J-8 Cobra bus : communication line for the connection of compatible Cobra sirens and sensors.
J-9 and J-10 CAN H/L : to connect as shown in the speci fi c vehicle CAN installation sheet.
J-11 Pager negative output : low power control signal for triggering a pager device or a telematic one. Active low during
alarm time.
J-12 CDL unlock negative output
: low power control signal to unlock central door locking. Activated by the Cobra remote
control , if provided (see electrical diagram F).
J-13 analogic input
: make the connection if required by the speci fi c vehicle CAN installation sheet.
J-14 12V connection (+30)
: the positive supply must be connected to a vehicle positive connection point upstream of the
fuse box. Fit a 15A fuse as close as possible to the connection point.
J-15 GND connection : the ground must be connected to a factory earth point or directly to the negative pole of the battery.
J-16 Negative output for modules
: active when the system is armed. To be used for the connection of compatible
Cobra modules.
J-17 Horn/loudspeaker negative output
: to program in line with the connected device. See electric diagrams and
functionalities programming tables. The output set automatically as per selected device, for horn choose also fi x or intermittent.
J-18 Positive input
: when connected to positive it disables permanently the automatic ultrasonic protection exclusion
normally working when windows are left open.
J-19 analogic input : make the connection if required by the speci fi c vehicle CAN installation sheet.
J-20 analogic input : make the connection if required by the speci fi c vehicle CAN installation sheet.
J-21 negative input to enter in programming procedure/to connect bonnet pushbutton : if connected to
ground the system will enter in the programming procedure for all applications not able to detect the original bonnet pushbutton.
If the siren is a wireless one this input must not be used for the bonnet pushbutton connections. For wired siren or loudspeaker
this input must be used for the connection of the bonnet pushbutton as indicated in the speci
fi c vehicle CAN installation sheet.