Cobra 4600 CAN, Руководство по установке

Страница: 7 / 20

INSTALLATION MANUAL 4600 CAN/PLIP
7
J-22 Do not connect.
J-23 Negative input for additional modules:
to be used as a triggering input for the connection of compatible Cobra
modules.
J-24 Do not connect.
J-25 CDL lock negative output : low power control signal to lock central door locking. Activated by the Cobra remote
control , if provided (see electrical diagram F).
J-26 analogic input : make the connection if required by the speci fi c vehicle CAN installation sheet.
26 ways connector J pin-out for PLIP con fi gurations
J-1 and J-2 Engine crank inhibition :
to get the maximum security level to the system connect the two wires as shown
in the electrical diagrams to prevent the engine starter running. During the cranking phase, measure the value of the current in the circuit
that has been interrupt, to make sure that it does not exceed the technical speci fi cations of the product. Install an additional relay if required.
J-3 Logic blinker output: make the connection if required by the speci fi c vehicle PLIP installation sheet.
J-4 Power blinker output : make the connection if required by the speci fi c vehicle PLIP installation sheet.
J-5 Logic blinker feedback input or power blinker output: make the connection if required by the speci fi c vehicle
PLIP installation sheet.
J-6 Blinker inhibition positive input : to connect as indicated in the speci fi c vehicle PLIP installation sheet or in the
product installation guide for PLIP applications available on the web under Application manuals.
J-7 Negative input for CDL opening switch signal
: to connect as indicated in the speci fi c vehicle PLIP installation
sheet or in the product installation guide for PLIP applications available on the web under Application manuals.
J-8 Cobra BUS:
communication line for the connection of compatible Cobra sirens and sensors.
J-9 and J-10 Do not connect.
J-11 Pager negative output : low power control signal for triggering a pager device or a telematic one. Active low during
alarm time.
J-12 CDL unlock negative output : low power control signal to unlock central door locking. Activated by the Cobra remote
control , if provided (see electrical diagram F).
J-13 Positive input for CDL motor opening signal : to connect as indicated in the speci fi c vehicle PLIP installation
sheet or in the product installation guide for PLIP applications available on the web under Application manuals.
J-14 12V connection (+30) : the positive supply must be connected to a vehicle positive connection point upstream of the
fuse box. Fit a 15A fuse as close as possible to the connection point.
J-15 GND connection
: the ground must be connected to a factory earth point or directly to the negative pole of the battery.
J-16 Negative output for modules
: active when the system is armed. To be used for the connection of compatible
Cobra modules.
J-17 Horn/loudspeaker negative output
: to program in line with the connected device. See electric diagrams and
functionalities programming tables. The output set automatically as per selected device, for horn choose also fi x or intermittent.
J-18 +15/54 connection: to be connected to a ignition key ON positive signal. The positive signal must be feeded while
starting the vehicle and when the engine is ON.
J-19 Negative input for CDL closing switch signal: to connect as indicated in the speci fi c vehicle PLIP installation
sheet or in the product installation guide for PLIP applications available on the web under Application manuals.
J-20 Do not connect.
J-21 negative input to enter in programming procedure/to connect bonnet pushbutton
: if connected to
ground the system will enter in the programming procedure for all applications not able to detect the original bonnet pushbutton.
If the siren is a wireless one this input must not be used for the bonnet pushbutton connections. For wired siren or loudspeaker
this input must be used for the connection of the bonnet pushbutton as indicated in the speci
fi c vehicle PLIP installation sheet.