8
PREPARATION AND SET-UP FOR YOUR NEW SPA
LOCATION FOR YOUR NEW SPA:
You want to keep in mind how you intend to use the spa and plan the location
accordingly.
How close is the spa from the exit or entrance to your house? (consider the
cold weather)
Is the path to your spa clean of debris, sand, grass? (so as not to track into the
spa)
Is there protection from wind, inclement weather?
Can neighbors or passersby see the spa?
NOTE:
Allow for service access:
Many spa owners enjoy placing their
spa in a decorative enclosure or a deck. Keep in mind that you need to
have access to the equipment for maintenance and the spa should be
able to be moved or lifted without destroying the special enclosure or its
surroundings. You should discuss this with your dealer when designing
the location. Extension cords are not to be used in conjunction with the
operations of the spa. Low voltage damage could result and this is not
covered by warranty.
NOTE:
All components must be 120V; No 240V
components allowable.
240VAC:
Depending on the model of spa, it will require either a 40 Amp,
50 Amp, or 60 Amp dedicated circuit breaker, GFCI, with the proper wire
size based on the length of the run. The electrical circuit must be in-
stalled by a certified electrician and approved by a local building or elec-
trical inspector.
ELECTRICAL REQUIREMENTS
All self contained spas use 120VAC or 240VAC electrical spa packs..
These instructions describe the only acceptable electrical wiring proce-
dures. Spas wired in any other way will void your warranty and may
result in serious injury. All installations should be completed by a certi-
fied electrician. Failure to comply with state and local codes may result
in fire or personal injury and will be the sole responsibility of the spa
owner.
120VAC:
This requires an isolated 20 Amp circuit breaker. This needs to
be an isolated circuit with no other appliances or lights on this circuit at
any time. Extension cords are not to be used in conjunction with the
operations of the spa. Low voltage damage could result and this is not
covered by warranty.
NOTE:
All components must be 120V; No 240V
components allowable.
240VAC:
Depending on the model of spa, it will require either a 40 Amp,
50 Amp, or 60 Amp dedicated circuit breaker, GFCI, with the proper wire
size based on the length of the run. The electrical circuit must be in-
stalled by a certified electrician and approved by a local building or elec-
trical inspector.
OWNER’S MANUAL
2017
SURFACE AND PAD REQUIREMENTS
Your new portable spa must be placed on a firm, flat and level surface,
so the spa weight is supported uniformly. We recommend no less than a
3” (93 mm) thick concrete slab. Wood decking or balconies must be con-
structed to support 150 pounds per square foot (730 kg/m²). Refer to
local and current building codes in your area. Consult an engineer
for live loads in your area. Should your new spa need to go through a
gate, the opening should be a minimum of 48 inches and up to 8.5’ over-
head clearance depending on the size of the unit.
NOTE:
Damage caused by alternate decking methods may avoid the spa
warranty. Contact your local dealer if you have any questions regarding
spa location or placement.
DRAINING AND WINTERIZING
DRAINING YOUR SPA
After a period of 3-4 months, detergent residues from bathing suits and
soap film will build up in your spa water. Once this happens, your spa
water will appear cloudy and should probably be replaced.
Turn power OFF at the breaker.
Locate the drain valve (usually in the equipment area).
Remove the safety cap and attach garden hose.
Drain water to a convenient area. (Spa water may harm grass or plants if sani-
tizer levels are high.)
When water begins to flow out of the hose, open the air relief valve located on
filter lid (Hydro-Cyclonic Filtration) or Air Bleeder Valve (Skim Filtration)
Your spa will drain except for a small portion left in the foot well. This can be
removed with a sponge and pail.
Once empty, clean as required.
To finish, remove garden hose and attach safety cap.
IMPORTANT (Cascade Series Only):
There will be an additional drain
valve. This is connected directly to the tank reservoir and you will see the
water level go down on the sight tube in the equipment area.
WINTERIZING YOUR SPA
In many areas of the world the temperature may drop below 32°F
(0°C). We recommend the spa is always filled with water and running at
normal spa temperatures. By doing this you will minimize the risk of
freezing within your spa. If it is necessary to leave your spa unattended
for long periods of time during cold weather conditions, you should drain
your spa to avoid accidental freezing caused by power outages.
Your local dealer can perform the following winterizing procedures, if you
are not completely comfortable with them.
Ensure that you have fully drained the spa (Refer to the DRAINING YOUR SPA
section)
After draining, your spa may still have water remaining in the equipment and
plumbing fittings. Disconnect the hand-tightened union fittings going to and from
the jet pumps. Be careful not to lose the o-rings between the unions and pump
housing.
Leave drain valve in the open position and safety cap off .
To completely drain the plumbing lines, a wet/dry shop vacuum can be used to
draw out any remaining water. Place the vacuum hose over the jet fittings in the
