background image

 

4

 

1.2  GENERAL INSTRUCTIONS 

 

Preliminaries

 

The positioning, hydraulic system, refrigerating, electrics and 
the channelisation of the air must be determined by the 
system designer in accordance with local regulations in force. 

Only qualified personnel can operate on the unit, as required 
by the regulation in force.  

Using the unit  in case of breakdown or malfunction :  

• 

voids the warranty 

• 

may compromise the safety of the machine 

• 

may increase time and repair costs. 

Follow local safety regulations. . 

Keep packing material out of children’s reach it may be 
dangerous. . 

Recycle and dispose of packing material in conformity with 
local regulations. . 

Risk situations

 

The unit has been designed and created to prevent injures to 
people.  

During designing it is not possible to plane and operate on all 
risk situation.  

Read carefully "Residual risk" section where all situation 
which may cause damages to things and injuries to people 
are reported.  

Installation, starting, maintenance and repair required specific 
knowledge; if they are carried out by inexperienced personnel, 
they may cause damages to things and injuries people.  

Intended use

 

Use the unit for cooling/heating water or a water and glycol 
mix for air-conditioning only, within limits defined in the 
technical bulletin and on this manual.. 

Any use other than intended does not involve the 
manufacturer in any commitment or obligation. . 

Installation

 

Verify that the electrical line characteristics are in compliance 
with data quotes on the unit serial number label. 

Maitenance

 

Plan periodic inspection and maintenance in order to avoid or 
reduce repairing costs. 

Turn the machine off before any operation.

 

Modification

 

All unit modifications will end the warranty coverage and the 
manufacturer responsibility. . 

Breakdown/Malfuction

 

Disable the unit immediately in case of breakdown or 
malfunction. . 

Contact a constructor certified assistance service. 

Use original spares parts only.  

User training

 

The installer has to train the user on : 

• 

 start-up / shutdown;  

• 

 set points change;  

• 

 standby mode;  

• 

 maintenance;  

• 

 what to do / what not to do in case of breakdown.  

Data update

 

Continual product improvements may imply manual data 
changes . 

Visit manufacturer web site for updated data

.  

Keep this manual with the wiring diagram in an accessible 
place for the operator.  

Note the unit lable data so you can provide them at the assi-
stance centre in case of intervention (see "Unit identification" 
section). 

Provide a machine notebook that allows any interventions 
carried out on the machine to be noted and tracked making it 
easier to suitably note the various interventions and aids the 
search for any breakdowns. 

In case of breakdown or malfunction: 

• 

immediately deactivate the unit . 

• 

contact a assistance service centre authorized by the 
manifacturer.  

• 

use original spares parts only  

Ask the installer to format on:  

• 

start-up / shutdown;  

• 

 set points change;  

• 

 standby mode;  

• 

 maintenance;  

• 

 what to do / what not to do in case of breakdown.  

1.3 INDICATIONS FOR THE USER 

 

The manual provides correct unit installation, use and 
maintenance. 

Pay particolar attention to: 

Warning identifies particularly important operations or 

 

information . 

Prohibited operations that must not be carried out, that 
compromise the operating of the equipment or may cause 
damage to persons or things. 

• 

It is advisable to read it carefully so you will save time 
during operations. 

• 

Follow the written indications so you will not cause 
damages to things and injuries people. The preliminary 
information must be read prior to carrying out any of the 
following operations.  

1.1  MANUAL

 

1 - GENERAL

 

Содержание WSH 100D

















































Отзывы: