ClimExel DH-120 Скачать руководство пользователя страница 14

Страница: 14 / 14

28/28

2015/12 - Indice de révision : B - Code : 33491

Error codes and trouble-shooting

Error codes:

Troubleshooting:

Symptom

Probable cause

Possible solution

The dehumidifer will

not switch on

Circuit breaker(s) or fuse tripped

Identify the reason for the fault, correct it

and reset the circuit breaker or replace the

fuse

On/ Off button set to off

Switch the machine on

Loose electrical connection

Verify that the remote installed control pad

cable and the power cable are correctly

tightened

In heating mode, the

air is circulating but

the air temperature

at the inlet is the

same as the air

temperature at the

outlet

T°C set point set to a temperature lower

than the ambient T°C

Modify the set point

3 minute time delay

Wait at least 5 minutes for the heating

element to reach temperature

Bad contact

Check that the heating element connections

are correctly tightened

If the problem is not resolved, contact the Procopi agent

Code

Meaning

Safety measure triggered

Faulty ambient air T° sensor (sensor or connection cable)

Shuts down the machine

Faulty defrosting sensor (sensor or connection cable)

The machine continues to run

Faulty humidity sensor (sensor or connection cable)

Shuts down the machine

Faulty exhaust air T° sensor (sensor or connection cable)

Turns off the heating element

Refrigerant T° sensor at the evaporator inlet is faulty (sensor or

connection cable)

The machine continues to run

HP safety mechanism tripped

Stops the compressor

LP safety mechanism tripped

Stops the compressor

Exhaust air thermal protection tripped

Turns off the heating element

Communication error

Shuts down the machine

Heating element thermal protection tripped

Turns off the heating element

Содержание DH-120















Результаты поиска

Содержание DH-120

Отзывы:

Бренды по названию

Популярные бренды

ClimExel DH-120, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DH-120

Отзывы:

Бренды по названию

Популярные бренды