background image

25/28

2015/12 - Indice de révision : B - Code : 33491

To modify the value of the parameter displayed, press the SET key. The value of the parameter will begin 

to flash, use the arrow keys (

 and 

) to modify the parameter. Press the SET key to validate the modi-

fication.  

 Press    or   .

 

„

Installation of the heating element (option) 

The heating element should only be installed by a qualified professional

.  

Parameter 

code

Parameter title

Allowed values

Default value

1

C1

With or without heating

0 without / 1 with

0

2

C2

Heating element temperature

From -20°C to +99°C

Value measured

3

C3

Humidity compensation to calibrate 

the humidity sensor

 From -5%  to  +5%

0%

4

C4

Minimum time lapse between two 

defrosting cycles

From 15Min to 90Min

20Min

5

C5

Defrosting cycle start temperature

From -10°C to 10°C

-1°C

6

C6

Defrosting cycle end temperature

From 0°C to 15°C

8°C

7

C7

Maximum duration of the defrosting 

cycle

From 2Min to 12Min

8Min

8

C8

Fan operation once the set point is 

reached

0 the fan stops at the set point  

/ 1 the fan switches to low speed at 

the set point

1

9

C9

Exhaust air temperature

-20°C~99°C

Measured value

10

CA

Refrigerant temperature at the 

evaporator inlet

-20°C~99°C

Measured value

11

Cb

EXV step no.

100~500P

Measured value

12

CC

Overheating target value

Between -20°C and +20°C

5°C

Stop the machine and cut the power supply to the dehumidifier.

1. 

Remove the plastic casing: extract the 2 Phillips head screws located 

midway up each side, and the 3 Phillips head screws on the bottom of 

the machine on each side. Also, to facilitate removal,  take the metallic 

strip off the back of the machine. Free the casing by pulling it forward. 

2. 

Place  the  element  flat  over  the  fins  and 

tube condenser with the black grating 

facing upwards and the connections 

oriented towards the electrical box. Feed 

the electrical wires through the opening 

located on the right hand side. 

 

Align the holes in the heating element plate 

with those of the base and insert the 4 

screws to attach the heating element 

to the machine. 

3. 

Open the lid of the electrical box 

Содержание DH-120















Отзывы: