CLIMAVENETA ACCURATE Скачать руководство пользователя страница 21

Страница: 21 / 28

English 01/07

ACCURATE AX* - AW*

TERMINAL AND BOARD CONFIGURATION

TROUBLESHOOTING

FILL AND DRAIN ASSEMBLIES

To ensure the correct operation of the humidifier, the supply/fill and
drain assemblies need to be inspected periodically.
Proceed as follows:

- completely drain the water from the boiler using the MANUAL

CONTROLS on the controller A1;

- disconnect the power supply by opening the main switch on the

electrical panel;

- remove the fill pipe from the 3/4 GAS fitting on the fill solenoid

valve;

- remove and clean the filter located inside the solenoid valve fit-

ting;

- dismantle the drain assembly (shown in Figure 13), clean the pipes

and remove any flakes of scale from the cup-drain trap.

Check for voltage; close the main switch.

The electrical panel is not powered

Check that the cutout IM in the auxiliary cir-
cuits is armed.
Check the fuse on the main board.

The auxiliary circuits are not powered

Check for DC power.

The control panel does not start the
air-conditioner.

FAULT

CAUSE

SOLUTION

THE AIR-CONDITIO-
NER DOESN'T START

See the controller manual.

The parameter settings on the microprocessor
controller are not correct.

See “LOW OR NO AIR FLOW”.

The air flow-rate is too low or null.

Check the electrical connections and the
configuration of the controller.

The probe isn't working.

Check the thermal load in the room being
air-conditioned.

Thermal load higher than expected.

Check the electrical connections to the valve
servomotor. Open the valve using the manual
control knob.

Three-way valve not working.

Check for the flow of chilled water; check that
any on-off valves outside of the unit are open.

No flow of chilled water.

Check the operation of the water chiller.

High temperature of the chilled water.

See “THE COMPRESSOR/COMPRESSORS
DON'T START”.

The compressor/compressors don't start,
despite being activated by the controller.

ROOM TEMPERATURE
TOO HIGH

Troubleshooting is simplified by the information provided by the
microprocessor controller: if an alarm is signalled, refer to the
control panel instruction manual.

If required, contact the nearest service centre, indicating the
probable causes of the fault.

Содержание ACCURATE





























Результаты поиска

Содержание ACCURATE

Отзывы:

Бренды по названию

Популярные бренды

CLIMAVENETA ACCURATE, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание ACCURATE

Отзывы:

Бренды по названию

Популярные бренды