CleaverBrooks ProFire Q Series Скачать руководство пользователя страница 66

Страница: 66 / 88

Troubleshooting

6-8

750-437

Q Series Full Modulation

Any #

Air pressure failure (speed-dependent air

pressure switch)

A fault occurred related to the speed-dependent air pressure switch. See diagnostic codes

for more information.

Air pressure switch off

When using a speed-dependent air pressure switch, the switch must be closed anytime the

VSD speed is greater than the setting of parameter 671.

Air pressure switch on

When using a speed-dependent air pressure switch, the switch must be open anytime the

VSD speed is less than the setting of parameter 670.

128

Invalid parameterization

Check the settings of parameters 670 and 671. Parameter 671 must be set to a higher

value than parameter 670.

Combustion pressure, POC - start

prevention

Check wiring and operation of combustion pressure switch.

Any #

Pressure switch-min (Pmin)

A fault occurred related to the low gas pressure switch. See diagnostic codes for more

information.

No minimum gas pressure

The low gas pressure switch (input X5-01.2) opened, causing a fault. Check gas supply

and open any manual shutoff valves. Check the setpoint and wiring of the low gas pressure

switch.

Gas shortage / prevention of startup

The low gas pressure switch was not made by the end of phase 22, preventing the startup

of the LMV3. See diagnostic code 0 for more corrective actions.

Any #

Pressure switch-max (Pmax) / POC

A fault occurred related to the high gas or oil pressure switch (or POC if using an LMV3 with

a software version V02.00). See diagnostic codes for more information.

Pressure switch-max (Pmax): Maximum

gas / oil pressure exceeded. POC: POC

open (software version V02.00)

The high gas / oil pressure switch (input X5-02.2) opened, causing a fault. Check the

setpoint and wiring of the high gas / oil pressure switch. Check pressure regulators for

ruptured diaphragms. If using an LMV3 with a software version V02.00, this could be a

POC fault if parameter 237 is set for 2. If so, see corrective action of error code 14,

diagnostic 0.

POC closed (software version V02.00) Only appears if using an LMV3 with a software version V02.00: See corrective action of

error code 14, diagnostic 1.

POC open - start prevention (software

version V02.00)

Only appears if using an LMV3 with a software version V02.00: See corrective action of

error code 14, diagnostic 64.

Error

Code Diag. Code Description

Corrective Action

Note: Diagnostic codes are additive. If a diagnostic code appears that is not on this list, it is a combination of multiple diagnostic codes.

Содержание ProFire Q Series

























































































Результаты поиска

Содержание ProFire Q Series

Отзывы:

Похожие инструкции для ProFire Q Series

Бренды по названию

Популярные бренды

CleaverBrooks ProFire Q Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание ProFire Q Series

Отзывы:

Похожие инструкции для ProFire Q Series

Бренды по названию

Популярные бренды