ClearWater AQUA ELITE 50 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

ClearWater AQUA ELITE 50 Скачать руководство пользователя страница 5

5

F). INSTALLING THE ELECTRODE

Generously wrap Teflon tape around the threaded part of the electrode assembly
several times. Screw electrode into the tee. Do not over tighten.

Power Source/

Pump Timer

Pump

Electrode

POOL

Filter

Heater

Kynar check valve
¼" reinforced vinyl hose
Venturi Injector
Clear view window

2" manifold with

venturi injector and

ball valve assembly

1½" reducer bushings (if needed)

water flow

N = Nylon Hose Clamps

N

N

N

N

G). INSTALLING THE VENTURI INJECTOR

N = Nylon Hose Clamps

Mount the venturi manifold on the return line (after the filter, pump, electrode chamber, heater, etc.) so it is the
last item before entering the pool. This is very important.

MAKE SURE THE WATER FLOWS IN THE DIRECTION OF THE ARROWS MARKED ON THE
VENTURI MANIFOLD.

The venturi manifold comes in two-inch pipe. If plumbing size is 1 ½", you will need to add 2" x 1 ½" reduced
bushings on each end of the manifold (included with the venturi manifold package.)

«
...
3
4
5
6
7
...
»

Содержание AQUA ELITE 50





















Отзывы:

Нет отзывов