ClearView IPD-81A Скачать руководство пользователя страница 73

Страница: 73 / 143

5.2.9 Bonjour

The Bonjour interface is shown as below. See Figure 5-41.

Bonjour is based on the multicast DNS service from the Apple. The Bonjour device can automatically

broadcast its service information and listen to the service information from other device.

You can use the browse of the Bonjour service in the same LAN to search the network camera device

and then access if you do not know the network camera information such as IP address.

You can view the server name when the network camera is detected by the Bonjour. Please note the

safari browse support this function. Click the “Display All Bookmarks: and open the Bonjour, system can

auto detect the network camera of the Bonjour function in the LAN.

Figure 5-41

5.2.10 Multicast

The multicast interface is shown as in Figure 5-42.

Multicast is a transmission mode of data packet. When there is multiple-host to receive the same data

packet, multiple-cast is the best option to reduce the broad width and the CPU load. The source host

can just send out one data to transit. This function also depends on the relationship of the group

member and group of the outer.

Note:



Open preview, streaming media protocol, select multicast, and monitor via multicast format.



Here you can set multicast address and port. You also need to go to Live interface to set the

protocol as Multicast.

Содержание IPD-81A
















































































































































Результаты поиска

Содержание IPD-81A

Отзывы:

Похожие инструкции для IPD-81A

Бренды по названию

Популярные бренды

ClearView IPD-81A, Руководство по эксплуатации

Результаты поиска

Содержание IPD-81A

Отзывы:

Похожие инструкции для IPD-81A

Бренды по названию

Популярные бренды