ClearView IPD-81A Скачать руководство пользователя страница 46

Страница: 46 / 143

5.1.1.9

Zoom and Focus

Note:

Only motorized vari-focal devices support focus and zoom function.

Step 1

Select “Setup > Camera > Conditions > Zoom and Focus” and the system will display the interface of

“Zoom and Focus” which is shown in Figure 5-11.

Figure 5-11

Step 2

Adjust the focal length of the lens.

After it is zoomed, set “Speed” and press “+”, “-“or drag the sliding block directly to adjust.

Step 3

Adjust the lens definition.

After it is focused, set “Speed” and press “+”, “-“or drag the sliding block directly to adjust.

Note:



Speed is used to set the length by pressing “+” and “-“.



After adjusting the focal length of the lens or click “Auto Focus”, the device will auto adjust the

image definition, it is not allowed to implement other lens operation during auto focus.



After several times of zoom and focus, the image fails to be adjusted clear, click “Restore All’ to

reset the lens to zero and remove the accumulative error of the lens.



Click “Refresh” and the device will automatically synchronize the hardware to the location of sliding

block of lens zoom and focus.

5.1.2 Video

Содержание IPD-81A
















































































































































Результаты поиска

Содержание IPD-81A

Отзывы:

Похожие инструкции для IPD-81A

Бренды по названию

Популярные бренды

ClearView IPD-81A, Руководство по эксплуатации

Результаты поиска

Содержание IPD-81A

Отзывы:

Похожие инструкции для IPD-81A

Бренды по названию

Популярные бренды