ClearView IPD-81A Скачать руководство пользователя страница 26

Страница: 26 / 143

4.1.1 Function of Play

The function of play is shown as in Figure 4-2 and Figure 4-3.

Figure 4-2

Figure 4-3

Parameter

Function

①

Play

When you see this button, it means pause or not played record. Click on this
button, switch to normal play status.

②

Stop

Click this button to stop playing.

③

Play by

frame

Click on this button to go to next frame.

Note:

You shall pause record when you use this function.

④

Slow

Click on this button to play slowly.

⑤

Quick

Click on this button to play quickly.

⑥

Silent

When this button displays, it means audio is silent. Click on this button to switch

back to normal.

⑦

Volume

Click on left mouse to adjust volume.

⑧

-1 Fisheye

Click this button and fisheye device can adjust display mode according to
different installation mode during the process of playback.

⑧

-2 Rule Info

Click the button and it will playback and display intelligent rules and object
detection box if the video is equipped with intelligent rule info after the function is
enabled, it is off by default.

Содержание IPD-81A
















































































































































Результаты поиска

Содержание IPD-81A

Отзывы:

Похожие инструкции для IPD-81A

Бренды по названию

Популярные бренды

ClearView IPD-81A, Руководство по эксплуатации

Результаты поиска

Содержание IPD-81A

Отзывы:

Похожие инструкции для IPD-81A

Бренды по названию

Популярные бренды